TP-Link JetStream TL-SG3424P User Manual Download Page 122

Page: 122 / 263

Configuration Procedure:

Step Operation

Description

1 Configure

IP-Range

Required.

Configure IP-Range to be filtered on

Multicast

→

Multicast Filter

→

IP-Range

page.

Configure multicast filter
rules for ports

Optional. Configure multicast filter rules for ports on

Multicast

→

Multicast Filter

→

Port Filter

page.

8.4 Packet Statistics

On this page you can view the multicast data traffic on each port of the switch, which facilitates you
to monitor the IGMP messages in the network.

Choose the menu

Multicast

→

Packet Statistics

to load the following page.

Figure 8-12 Packet Statistics

The following entries are displayed on this screen:

Auto Refresh

Auto Refresh:

Select Enable/Disable auto refresh feature.

Refresh Period:

Enter the time from 3 to 300 in seconds to specify the auto refresh
period.

113

Summary of Contents for JetStream TL-SG3424P








































































































































































































































































Search results

Summary of Contents for JetStream TL-SG3424P

Reviews:

Related manuals for JetStream TL-SG3424P

Brands by name

Popular brands

TP-Link JetStream TL-SG3424P, User Manual

Search results

Summary of Contents for JetStream TL-SG3424P

Reviews:

Related manuals for JetStream TL-SG3424P

Brands by name

Popular brands