Toshiba Tecra 730CDT Page 47 Maintenance Manual Download | Manualshive

Page: 47 / 230

background image

730CDT

2-23

Procedure 1

Partition Check

Insert the Toshiba MS-DOS system disk into the disk drive, turn on the computer, then
perform the following checks:

Check 1

Type

C:

and press

Enter

. If you cannot change to drive C, go to Check 2. If you

can change to drive C, go to Procedure 2.

Check 2

Type

FDISK

and press

Enter

. Choose the Display Partition Information option

from the FDISK menu. If the C drive is listed, go to Check 3. If the C drive is
not listed, return to the FDISK menu, choose the option to create a DOS partition
on drive C, then recheck the system. If the problem still exists, go to Procedure 2.

Check 3

If the C drive is listed as active in the FDISK menu, go to Check 4. If the C drive
is not listed as active, return to the FDISK menu, choose the option to set the
active partition for drive C, then recheck the system. If the problem still exists,
go to Procedure 2.

Check 4

Remove the system disk from the FDD and cold boot the computer. If the prob-
lem still exists, go to Procedure 2. Otherwise, the HDD is operating normally.

Procedure 2

Message Check

When the computer's HDD does not function properly, one or more of the following error
messages may appear on the display. Start with Check 1 and perform the other checks as
instructed.

Check 1

If any of the following messages display, perform Check 5. If they do not appear,
perform Check 2:

HDC ERROR

(After 5 seconds this message will disappear.)

or

HDD #0 ERROR

(After 5 seconds this message will disappear.)

or

HDD #1 ERROR

(After 5 seconds this message will disappear.)

Check 2

If either of the following messages display, perform Check 3. If they do not
appear, perform Check 5.

Insert system disk in drive
Press any key when ready .....

or

Non-System disk or disk error
Replace and press any key

«
...
45
46
47
48
49
...
»

Summary of Contents for Tecra 730CDT







































































































































































































































Reviews:

No comments

Related manuals for Tecra 730CDT

Brand: IBM Pages: 18

Brand: IBM Pages: 152

DECstation 316+

Brand: DEC Pages: 94

Vehicle-Mount Computer 8515

Brand: Psion Teklogix Pages: 190

Brand: IBM Pages: 167

Brand: Matrox Pages: 174

Brand: Epson Pages: 117

Brand: Epson Pages: 184

CW3S16 Canadian Product

Brand: Epson Pages: 218

Brand: Epson Pages: 115

Brand: Epson Pages: 180

VisuNet GXP PC-GXP1100-22F

Brand: Pepperl+Fuchs Pages: 54

PCG-VX88 VAIO User Guide (primary manual)

Brand: Sony Pages: 1

Brand: Sony Pages: 2

Brand: Sony Pages: 14

Brand: Sony Pages: 1

PCG-K47 - VAIO - Mobile Pentium 4 3.2 GHz

Brand: Sony Pages: 1

PCG-K45 - VAIO - Mobile Pentium 4 3.2 GHz

Brand: Sony Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands