Toshiba Satellite Z930 Maintenance Manual Download Page 315

Page: 315 / 423

4 Replacement Procedures

4-32

[CONFIDENTIAL]

PORTÉGÉ Z930/Satellite Z930 Maintenance Manual (960-887)

Installing the Fin

To install the fin, follow the steps below and refer to Figure 4-14.

When silicon grease is already applied to the CPU, wipe them off with a cloth in
advance.

Apply new

grease

(Shin-Etsu Chemical Co. X-23-7921-5) on the CPU using a

special syringe as shown in the following figure.

NOTE: Apply new grease as shown in the figure below.

Set the

fin

in place and secure it with the following

screws





3.5C

BIND



NOTE: When securing the fin, be sure to secure the screws in the order of the number

marked on the fin.

Summary of Contents for Satellite Z930








































































































































































































































































































































































































































Search results

Summary of Contents for Satellite Z930

Reviews:

Related manuals for Satellite Z930

Brands by name

Popular brands

Toshiba Satellite Z930, Maintenance Manual

Search results

Summary of Contents for Satellite Z930

Reviews:

Related manuals for Satellite Z930

Brands by name

Popular brands