Toshiba Satellite Z930 Maintenance Manual Download Page 332

Page: 332 / 423

4 Replacement Procedures

PORTÉGÉ Z930/Satellite Z930 Maintenance Manual (960-887)

[CONFIDENTIAL]

4-49

Installing the Keyboard

To install the keyboard, follow the steps below and refer to Figure 4-22.

Stick a new

insulator

(INSU KB) on the cover assembly.

Peel off the separator of the insulator (INSU KB).

NOTE: When sticking an INSU KB to COVER ASSY, refer to the following figure.

Stick a new

keyboard

on the insulator (INSU KB).

NOTE: Arrange the KB flexible cable and KB BL flexible cable as shown in the figure

below.

Summary of Contents for Satellite Z930








































































































































































































































































































































































































































Search results

Summary of Contents for Satellite Z930

Reviews:

Related manuals for Satellite Z930

Brands by name

Popular brands

Toshiba Satellite Z930, Maintenance Manual

Search results

Summary of Contents for Satellite Z930

Reviews:

Related manuals for Satellite Z930

Brands by name

Popular brands