Toshiba Satellite Z930 Maintenance Manual Download Page 312

Page: 312 / 423

4 Replacement Procedures

PORTÉGÉ Z930/Satellite Z930 Maintenance Manual (960-887)

[CONFIDENTIAL]

4-29

4.7 DC

fan

Removing the DC fan

To remove the DC fan, follow the steps below and refer to Figure 4-13.

Disconnect the

fan harness

from the connector

CN3380

on the system board.

Remove the following

screws

securing the DC fan.



M2.5



FLAT

HEAD



Remove the

DC fan

from the slot.

Figure 4-13 Removing the DC fan

CN3380

DC fan

M2.5x5C FLAT HEAD

Fan harness

Summary of Contents for Satellite Z930








































































































































































































































































































































































































































Search results

Summary of Contents for Satellite Z930

Reviews:

Related manuals for Satellite Z930

Brands by name

Popular brands

Toshiba Satellite Z930, Maintenance Manual

Search results

Summary of Contents for Satellite Z930

Reviews:

Related manuals for Satellite Z930

Brands by name

Popular brands