manualshive.com logo in svg

Toshiba Satellite Z930, Maintenance Manual

The Toshiba Satellite Z930 Maintenance Manual is a comprehensive user guide providing step-by-step instructions for maintaining and troubleshooting your laptop. Download this free manual from our website to easily access essential information on upkeep and optimal performance.

Share
Download
background image

   

  Troubleshooting Procedures  

PORTÉGÉ Z930/Satellite Z930 Series Maintenance Manual (960-887)  [CONFIDENTIAL]

 2-33 

2.5.2  Procedure 2 Diagnostic Test Program Execution Check 

Insert the Diagnostics Disk (CD) in the ODD, turn on the computer and run the test. Refer to 
Chapter 3, 

Tests and Diagnostics,

 for more information about the diagnostics test procedures. 

Make sure the floppy disk is formatted correctly and that the write protect tab is disabled. 
Floppy disk drive test error codes and their status names are listed in Table 2-7. If any other 
errors occur while executing the FDD diagnostics test, go to Check 1. 

Table 2-5  FDD error code and status 

Code Status 

01h Bad 

command 

02h 

Address mark not found 

03h Write 

protected 

04h 

Record not found 

06h Media 

replaced 

08h DMA 

overrun 

error 

09h DMA 

boundary 

error 

10h CRC 

error 

20h FDC 

error 

40h Seek 

error 

60h FDD 

not 

drive 

80h 

Time out error (Not ready) 

EEh Write 

buffer 

error 

FFh 

Data compare error 

 

Check 1 

If the following message is displayed, disable the write protect tab on the floppy 
disk by sliding the write protect tab to “write enable”. If any other message appears, 
perform Check 2. 

Write protected

 

Check 2 

Make sure the floppy disk is formatted correctly. If it is, go to Procedure 3. 

Summary of Contents for Satellite Z930








































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite Z930

NEC VERSA SX HARD DISK DRIVE Upgrade Manual preview
VERSA SX HARD DISK DRIVE
Brand: NEC Pages: 6
NEC Versa LX Product Manual preview
Versa LX
Brand: NEC Pages: 46
NEC Versa LX User Manual preview
Versa LX
Brand: NEC Pages: 96
IBM 365xX Hardware Maintenance Manual preview
365xX
Brand: IBM Pages: 222
UMAX Technologies visionbook 14WRx User Manual preview
visionbook 14WRx
Brand: UMAX Technologies Pages: 72
Ace ASPIRE S7-191 Quick Manual preview
ASPIRE S7-191
Brand: Ace Pages: 366
Aspire TravelMate 2420 Series Service Manual preview
TravelMate 2420 Series
Brand: Aspire Pages: 108
Acer Aspire 5500 Manual Do Utilizador preview
Aspire 5500
Brand: Acer Pages: 92
Lenovo 320C-15IKB Hardware Maintenance Manual preview
320C-15IKB
Brand: Lenovo Pages: 84
Lenovo 3i-15 Chromebook User Manual preview
3i-15 Chromebook
Brand: Lenovo Pages: 42
Lenovo 2765T2U Brochure preview
2765T2U
Brand: Lenovo Pages: 4
Lenovo 2842F7U Brochure preview
2842F7U
Brand: Lenovo Pages: 4
Lenovo 3000 V100 Hardware Maintenance Manual preview
3000 V100
Brand: Lenovo Pages: 108
Lenovo 3249ERU Brochure preview
3249ERU
Brand: Lenovo Pages: 4
Lenovo 32597CU Brochure preview
32597CU
Brand: Lenovo Pages: 6
Lenovo 28762JU Brochure preview
28762JU
Brand: Lenovo Pages: 4
Lenovo 32492EU Brochure preview
32492EU
Brand: Lenovo Pages: 4
Lenovo 35089CU Specifications preview
35089CU
Brand: Lenovo Pages: 4

Brands by name

Popular brands

Load more brands