background image

 

27 

 

 

Normal      missing marking      smearing 

 
when  starting  of  marking  a  concecutive  touch  of  a  charactors,  the  high  air  pre
ssure  is  being  opened,  thus  to  drive  the  marking  needle  punching  and  marking
  on  parts  with  a  high  frequency,  but  du  to  the  air  refilling  for  the  pressure  ne
eds  a  bit  of  time,  if  within  this  period  the  needel  is  already  started  marking,  b
ut  the  high  pressure  is  not  arriving,  there  may   
emerged  a  missing  marking  phenomenon,  for  avoiding  this  situation,  it  after  th
e  high  pressure  air  switch  is  open,  let  the  meedel  stay  for  a  while  and  then  to
  start  is,  this  waiting  time  we  called  it  as  time  delay  of  marking.  Normally  it 
will  delay  within  2-8  milliseconds

 

 
after  each  successive  strokes  of  the  character  is  finish,  high-pressure  gas  source
  will  be  closed,  but  due  to  the  inflated  high-pressure  gas  pipeline  may  have  so
me  residue  gas  which  is  not  released,  if  by  now  the  needle  starts  to  move,  the
n  this  residue  pressure  may  drive  the  needle  in  high-frequency  and  punching  o
n  the  parts  to  make  a  smearing., In  order  to  avoid  such  situations  arise,  after  t
he  closure  of  the  high-pressure  gas  source,  let  the  marking  needle    stop  for  a 
short  period  of  time,  so  that  you  can  effectively  avoid  smearing. This  is  a  shor
t  pause  of  the  time  we  referred  to  as  "  smearing  ",  this  waiting  time  we  calle
d  it  time  delay  of  marking,  as  well  as  marking  needle  lift  up  time  delay.  Nor
mally  this  delay  will  will  carry  on  for  2-8  milliseconds

 

"time  delay  on  needle  up"  and  "and  needle  down"  is  fairly  simple  to  set,  directley 
input a time delay parameter into the text box at the right corner is OK.   
 
If your marking machine installed with a pneumatic clamps, you can set a time delay 
for the fixture, to make it have enough time for clampping the parts and moving the 
parts to a marking position after the marking start buttom is being pressed dwon.this 
time delay we called it clampping time delay 
   
Because  marking  machine  is  mechanical  devices,  so  after  repeatedly    marking, 
minor  deviations  may  occurred,  if  such  errors  does  not  be  corrected,  it  will 
accumulate the mistake  and eventually it will leading larger deviation, Therefore, an 
automatic  reset  function  is  designed  for  correct  such  errors. The  number  of  marking 
time and the complexity of marking will determin the times of auto-reset,normally, by 
each 200 marking or so    on an automatically reset is needed. This parameter we call 
"reset number of times." 

Summary of Contents for HS-DP Series


































Reviews: