THOMSON 510062 Connecting Manual Download | Manualshive

Page: 25 / 64

background image

25

EN

EN

www.mythomson.com

MOTOR DRIVE FOR 2-PANEL GATES - CONNECT

C - INSTALLATION

• Motor disengagement

• Disengage the motors in order to manually manoeuvre the arms.
• Open the gate up to the side stops.
• Turn the pivoting arm to press the gate bracket against

the gate as far as possible from the hinges

:

• Mark the holes for fastening the bracket on the gate.

Important:

The ends of the right arms should be at the middle of the rigid part of the gate so that the

pivoting arms are completely horizontal.

«
...
23
24
25
26
27
...
»

Summary of Contents for 510062

































































Reviews:

No comments

Related manuals for 510062

Brand: FAAC Pages: 25

Brand: FAAC Pages: 15

Brand: FAAC Pages: 12

Brand: FAAC Pages: 30

Brand: CAME Pages: 12

Brand: Salton Pages: 21

Brand: Chamberlain Pages: 96

SPACELITE HT150

Brand: BUTZBACH Pages: 45

Brand: GiBiDi Pages: 16

Brand: SOMFY Pages: 36

Brand: SOMFY Pages: 52

EaziClean BCO-50

Brand: Lincoln Redco Pages: 2

Brand: CAME Pages: 128

Brand: GDS Pages: 9

GDS 550P Series

Brand: GDS Pages: 15

Brand: GDS Pages: 17

Brand: GDS Pages: 17

Brand: Jaytech Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands