Thermo Scientific Orion Star, User Manual

Page: 18 / 368

Thermo Scientific Orion Star
™
and Star Plus Meter User Guide EN-12
Setup Menu Table
The following table is for the complete line of Orion Star and Star Plus meters .
Meters may not include all of the options listed in this table .
Top Line Middle Line Bottom Line Setup Menu Description (default setting, method specific)
PH rES 0.1, 0.01, 0.001 pH measurement resolution (0.01, yes)
PH bUF USA, EUr0 pH buffer set for automatic buffer recognition during calibration,
USA buffers are 1.68, 4.01, 7.00, 10.01, 12.46 and EUrO buffers
are 1.68, 4.01, 6.86, 9.18
(USA, yes)
ISE rES 1, 2, 3 ISE measurement resolution in significant figures (1, yes)
ISE UnIt m, mgL, PEr, PPb, n0nE ISE measurement units
(PPb, yes)
ISE rAng L0w, HIgH ISE concentration range for calibration stability criteria
(HIgH, yes)
ISE nLIn AUt0, 0FF ISE automatic blank correction for low-level calibration (AUt0, yes)
C0nd tC 0FF, LIn, nLF Conductivity temperature compensation type, LIn is for linear,
nLF is for non-linear pure water samples
(LIn, yes)
C0nd C0EF 0.0 to 10.0 Conductivity temperature compensation coefficient in % change
in conductivity per °C, appears if LIn was selected for tC
(2.1, yes)
C0nd tdSF 0.00 to 10.0 Conductivity TDS factor value
(0.49, yes)
C0nd CELL 0.001 to 199.0 Conductivity default cell constant value for automatic conductivity
calibration mode
(0.475, yes)
C0nd trEF 5, 10, 15, 20, 25 Conductivity reference temperature (25, yes)
C0nd tyPE Std, 1, 2, 3, 4, 5, 6, 7, USP Conductivity cell type and selectable range. Std is for standard,
USP is for planar, 1 through 7 for fixed ranges
(Std, yes)
See the RDO Optical Dissolved Oxygen Setup Menu section for details on the RDO probe information menus.
d0 rES 0.1, 1 % sat DO % saturation measurement resolution
(0.1, yes)
d0 rES 0.01, 0.1 mg/L DO mg/L measurement resolution
(0.01, yes)
d0 bAr AUt0, mAn DO barometric pressure compensation type (AUt0, yes)
d0 PrES 450.0 to 850.0 DO manual barometric pressure compensation value, appears
if mAn was selected for bAr
(760.0, yes)
d0 SAL AUt0, mAn DO salinity correction type (AUt0, yes)
d0 SALF 0 to 45 DO manual salinity correction value, appears if mAn was selected
for SAL or a DO meter without a conductivity mode is used
(0, yes)
d0 CALt AIr, H20, mAn, SEt0 DO calibration type
(AIr, yes)
d0 LIFE 365 to 0 Optical cap replacement countdown in days – 3, 4 and 5 Star Plus
RDO meters only
(Set by RDO probe, no)
dUE PH 0 to 9999 pH calibration alarm value in hours, 0 is off (0, yes)
dUE 0rP 0 to 9999 ORP calibration alarm value in hours, 0 is off (0, yes)
dUE ISE 0 to 9999 ISE calibration alarm value in hours, 0 is off (0, yes)
dUE C0nd 0 to 9999 Conductivity calibration alarm value in hours, 0 is off
(0, yes)
dUE d0 0 to 9999 DO calibration alarm value in hours, 0 is off (0, yes)
Meter Setup