Thermo Scientific Nicolet Summit OA User Manual Download | Manualshive

Page: 56 / 67

background image

c. Lift the crystal plate straight up off the instrument.

d. Use a clean, dry cloth to clean the area around the flange, under the area the plate sits.

3. Remove the instrument cover.

a. Carefully tilt the instrument onto its back so that it rests on the heat fins.

b. Using the 7/64 hex key, loosen the four screws fastening the cover to the instrument base.

c. Carefully tip the instrument back onto its feet. When you tip the instrument back up, the four

screws will fall out. Be careful not to lose them.

d. Lift the cover straight up off the base.

Thermo Scientific

Nicolet Summit OA Spectrometer User Guide

53

Maintenance

«
...
54
55
56
57
58
...
»

Summary of Contents for Nicolet Summit OA




































































Reviews:

No comments

Related manuals for Nicolet Summit OA

Endura AZ20 series

Brand: ABB Pages: 8

Brand: Medeli Pages: 14

Brand: DAKOTA ULTRASONICS Pages: 50

Brand: Jamar Pages: 4

Brand: Kawai Pages: 64

Brand: Kawai Pages: 28

Brand: Kawai Pages: 28

Brand: Panasonic Pages: 1

Brand: UEi Pages: 5

Brand: Sonel Pages: 84

Brand: PASCO Pages: 4

DELMHORST J-2000

Brand: ABQ Industrial Pages: 4

Brand: General Pages: 12

Brand: Bartec Pages: 38

Brand: Ecodhome Pages: 12

Brand: Major tech Pages: 16

Brand: International Light Technologies Pages: 19

Brand: KATA Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands