Thermo Scientific Nicolet Summit OA User Manual Download | Manualshive

Page: 26 / 67

background image

11. Select Advanced options.

12. Under Advanced options, select System Image Recovery.

13. Select Windows 10 as the target operating system.

14. In the “Select a system image backup” window, use the latest available system image or select

another system image. Click Next.

Thermo Scientific

Nicolet Summit OA Spectrometer User Guide

23

Get Started with Your Nicolet Summit OA Spectrometer

«
...
24
25
26
27
28
...
»

Summary of Contents for Nicolet Summit OA




































































Reviews:

No comments

Related manuals for Nicolet Summit OA

Brand: Tactical Controls Pages: 11

Brand: FarmChem Pages: 8

Brand: Hach Pages: 145

Brand: Hach Pages: 358

Polymetron 9582sc

Brand: Hach Pages: 280

Brand: HACH LANGE Pages: 15

Brand: Raytech Pages: 18

Brand: Tavool Pages: 12

Brand: ZHYQ Pages: 6

Brand: Autometers Systems Pages: 16

Brand: DriveTest Pages: 24

Brand: Mannix Pages: 5

Brand: Reed Instruments Pages: 14

Brand: Saluki Technology Pages: 161

Brand: Endress+Hauser Pages: 24

Brand: NARDA Pages: 60

Brand: Omega Pages: 24

Brand: Oceanic Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands