Thermo Scientific Nicolet Summit OA User Manual Download | Manualshive

Page: 25 / 67

background image

Get Started with Your Nicolet Summit OA Spectrometer

l

USB recovery drive

l

SSD with your system image

❖

To restore your system using the recovery drive and system image

1. Turn off the Summit spectrometer.

2. Connect an external keyboard to one of the Summit spectrometer’s USB ports.

3. Connect the USB recovery drive to one of the USB ports.

4. Turn the system on.

5. When the screen shows the Thermo Scientific splash screen, tap “Esc” on the keyboard several

times to open the system BIOS.

If a popup dialog shows “Quit Without Saving?” use the arrow keys to select No.

6. Using the arrow keys, navigate to the Save & Exit tab.

7. Navigate to the Boot Override section and select your recovery flash drive. Hit Enter to boot to the

recovery image.

8. When the “Choose your keyboard layout” screen appears, remove the recovery flash drive from

the USB port and insert the system image SSD.

9. Select your preferred keyboard layout.

10. In the Choose an Option screen, select Troubleshoot.

22

Nicolet Summit OA Spectrometer User Guide

Thermo Scientific

«
...
23
24
25
26
27
...
»

Summary of Contents for Nicolet Summit OA




































































Reviews:

No comments

Related manuals for Nicolet Summit OA

Brand: Bacharach Pages: 64

Blancett B3100 Series

Brand: Badger Meter Pages: 16

Brand: Badger Meter Pages: 26

Brand: Badger Meter Pages: 48

Brand: F&F Pages: 2

Brand: Bartington Pages: 15

Brand: Bartec Pages: 216

Brand: YOKOGAWA Pages: 2

Brand: ECO Sensors Pages: 22

Brand: ECO Sensors Pages: 7

Brand: F&F Pages: 24

Brand: QMI Pages: 54

Brand: JGR Pages: 12

Brand: OBD Pages: 5

Brand: R&S Pages: 248

Brand: Conrad Electronic Pages: 38

Sensorex SX41170SI

Brand: Meggitt Pages: 19

Speedrite Fault Finder

Brand: Tru-Test Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands