Thermo Scientific Nicolet Summit OA User Manual Download | Manualshive

Page: 41 / 67

background image

Options and Accessories

a. Carefully lower the cover over the base while routing the purge tube into the cover slot.

b. Lower the cover completely. As the cover is lowered into place, the purge tube is trapped in

the slot between the cover and the heat sink.

c. With the purge tube pushed to the side, tilt the instrument onto its back, resting on the heat

fins.

d. Insert the four screws that you removed previsously. Tighten all screws.

e. Tip the instrument back onto its feet.

f. Push the excess length of tubing into the instrument, or pull it out as needed.

38

Nicolet Summit OA Spectrometer User Guide

Thermo Scientific

«
...
39
40
41
42
43
...
»

Summary of Contents for Nicolet Summit OA




































































Reviews:

No comments

Related manuals for Nicolet Summit OA

Brand: jenway Pages: 20

Brand: X-Rite Pages: 45

Brand: X-Rite Pages: 22

Brand: TSI Instruments Pages: 4

Brand: Gates Pages: 112

Brand: TAC Pages: 28

Brand: SEAWARD Electronic Pages: 57

Brand: Isspro Pages: 2

Brand: iSTEK Pages: 15

ProScale 950 Series

Brand: Accurate Technology Pages: 16

Brand: Omega Pages: 14

Brand: Ress Pages: 11

Brand: Hanna Instruments Pages: 2

Brand: LI-COR Pages: 92

Brand: Efergy Pages: 24

Brand: HW Group Pages: 12

Brand: A&D Pages: 2

Brand: Bauhn Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands