Thermo Scientific LCQ Fleet Getting Started Manual Download Page 15

Page: 15 / 74

Thermo Scientific

LTQ Series Getting Connected Guide

Line Power, Vacuum System, Gases, and
Ethernet Communication

This chapter describes how to connect the LTQ Series MS detector to line power, the
forepump, necessary gases, and the data system computer.

Connecting the MS Detector to Line Power

To connect the LTQ Series MS detector to line power

1. Turn the Main Power circuit breaker to the Off (O) position.

2. Make sure that the Electronics switch is in the Service Mode position.

3. Connect the female plug of the power cord to the POWER IN receptacle of the power

panel.

4. Connect the male plug of the power cord to the 230 V ac power source in your

laboratory.

Contents

•

Connecting the MS Detector to Line Power

•

Connecting the Forepump to the LCQ Fleet or LXQ MS Detector

•

Connecting the Forepumps to the LTQ XL MS Detector

•

Connecting the Gases to the MS Detector

•

Connecting the MS Detector to the Data System Computer

CAUTION

If your local area is subject to power fluctuations or power interruptions, you

must install a power conditioning device or an uninterruptible power supply (UPS) in
your laboratory. For more information, refer to the

LTQ Series

Preinstallation Requirements

Guide

. The UPS must be certified by both North American (UL, CSA) and European

Agencies (TUV, UDE, SEMKO, DEMKO, and so on).

Summary of Contents for LCQ Fleet











































































Search results

Summary of Contents for LCQ Fleet

Reviews:

Related manuals for LCQ Fleet

Brands by name

Popular brands

Thermo Scientific LCQ Fleet, Getting Started Manual

Search results

Summary of Contents for LCQ Fleet

Reviews:

Related manuals for LCQ Fleet

Brands by name

Popular brands