Thermo Scientific LCQ Fleet Getting Started Manual Download Page 23 | Manualshive

Page: 23 / 74

background image

1

Line Power, Vacuum System, Gases, and Ethernet Communication

Connecting the MS Detector to the Data System Computer

Thermo Scientific

LTQ Series Getting Connected Guide

9

Connecting the MS Detector to the Data System Computer

The data system for the LTQ Series MS detector consists of a computer, a monitor, and an
optional printer. The LTQ Series MS detector communicates with the data system computer
through an Ethernet cable.

Y

To connect the MS detector to the data system computer

1. Connect a category five network (Ethernet) cable (P/N 00302-01838) to the

ETHERNET 100 BASE-T connector located on the MS detector power panel.

2. Connect the opposite end of the Ethernet cable to the 10/100 Base-T Ethernet switch

(P/N 00825-01015) provided with the MS detector.

3. Connect a second Ethernet cable (P/N 00302-01838) from the Ethernet switch to the

Ethernet card on the data system computer labeled Surveyor MS.

4. Connect the Ethernet switch to line power.

«
...
21
22
23
24
25
...
»

Summary of Contents for LCQ Fleet











































































Reviews:

No comments

Related manuals for LCQ Fleet

Brand: Raymarine Pages: 464

Brand: 3M Pages: 8

Brand: ZOLL Pages: 3

Brand: UNIA Pages: 62

Brand: R2 Pages: 20

Brand: MAGSTIM Pages: 86

Brand: zapco Pages: 14

Brand: K-SPORT Pages: 5

LUNAQUA Classic LED

Brand: Oase Pages: 16

Brand: VaBroom Pages: 4

Brand: Cuisinart Pages: 159

DJ Laptop stand +tray

Brand: Power Dynamics Pages: 3

Brand: IMG STAGELINE Pages: 2

Brand: Klippan Pages: 8

Brand: Kewtech Pages: 32

Brand: nox Pages: 2

Brand: KUHN Pages: 92

tynetec Aidcall

Brand: LEGRAND Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands