Themis USPIIi-1v Hardware Manual Download Page 40

Page: 40 / 128

USPIIi-1v Hardware Manual

4-6

Themis Computer

• Reads non-volatile RAM (NVRAM) and executes the boot sequence. The Diagnostic Executive or

standalone programs can also be executed.

• Includes the abbreviated system monitor. Entry into the system monitor is signified by the “ok” prompt.

If a boot attempt fails, the OBP tries to start the abbreviated system monitor.

• Supplies program code for the FORTH Toolkit; the on-board diagnostics contain the FORTH Toolkit

and the FORTH language interpreter. Entry into the FORTH Toolkit is signified by the “ok” prompt.

For more information on the OBP please refer to the

OpenBoot Command Reference

from Sun Microsystems

and to the “USPIIi-1v Software Manual”.

Summary of Contents for USPIIi-1v

































































































































Search results

Summary of Contents for USPIIi-1v

Reviews:

Related manuals for USPIIi-1v

Brands by name

Popular brands

Themis USPIIi-1v, Hardware Manual

Search results

Summary of Contents for USPIIi-1v

Reviews:

Related manuals for USPIIi-1v

Brands by name

Popular brands