Themis USPIIi-1v Hardware Manual Download Page 17 | Manualshive

Page: 17 / 128

background image

Themis Computer

1-3

1. Introduction

• A Micro DB9 connector to Male, DB25 Console adapter cable for the Baseboard Console (TTY A)

port; Themis Part Number 108113.

• A 68 pin, Sub-Miniature connector to 0.005”, male standard SCSI-3 connector adapter cable for the

Baseboard SCSI A; Themis Part Number 108712.

• A Paddle Board, Themis Part Number 105581. This paddle board must be connected behind the first

slot occupied by the USPIIi-1v board

• A 68 pin, SCSI-3 ribbon cable for the paddle board SCSI (SCSI A); Themis Part Number 108432.

The INT-KIT-USPIIi-1V/2-VME integration kit includes:

• The INT-KIT-USPIIi-1V/1-VME integration kit
• A second Paddle Board, Themis Part Number 105581. This paddle board must be connected behind the

second slot occupied by the USPIIi-1v board

• A second 68 pin, SCSI-3 ribbon cable for the second paddle board SCSI (SCSI B); Themis Part Number

108432.

• A Micro DB9 connector to Sun type 5 Keyboard and Mouse connector (Din-8) adapter cable; Themis

Part Number: 108783.

• A 26 pin, Male, Amplimite connector to a DB25 connector Adapter Cables for Serial Ports C or D;

Themis Part Number 108376.

• A 26 pin Male, Amplimite connector to DB25 printer cable for the Parallel Port; Themis Part Number

104077.

Please report any discrepancies to Themis Computer customer support immediately.

Remove the USPII

i

-1v board from its antistatic wrapping and verify that it is in the ordered configuration. For

information on the available configurations and their appearances refer to Chapter 3, "Specification."

1.5

How to Start Quickly

To start quickly with the USPII

i

-1v Themis Computer recommends that you read the following sections:

• Chapter 2, "Installation," This appendix contains vital information on configuring the USPII

i

-1v and the

design and setup of VMEbus based systems.

• Consult Appendix B, "Jumper and Solder Bead Configurations." This appendix contains a complete

listing of all user configurable jumpers and the default settings. Verify that the jumpers on your board
are set to meet your application requirements.

In addition to the USPIIi-1v hardware manual, the USPIIi-1v software manual (Themis P/N 108966) contains
information on software registers, address maps, additional Openboot commands as well as a description of
the Themis Computer VME software package for Solaris.

«
...
15
16
17
18
19
...
»

Summary of Contents for USPIIi-1v

































































































































Reviews:

No comments

Related manuals for USPIIi-1v

Brand: ECS Pages: 56

Brand: Texas Instruments Pages: 22

JW-A880GM-FUSION

Brand: J&W Pages: 38

B85 Anniversary

Brand: ASROCK Pages: 148

Brand: Navia Pages: 26

FEBFL7701_L31H008A

Brand: Fairchild Pages: 24

Brand: Raptor Pages: 59

TPS628436-7-8EVM-167

Brand: Texas Instruments Pages: 15

Brand: Hanasis Pages: 31

Brand: JETWAY Pages: 47

Brand: Acrosser Technology Pages: 3

Brand: Seanix Pages: 54

Brand: MSI Pages: 106

Thunder HEsl S2567

Brand: TYAN Pages: 60

Brand: ASROCK Pages: 92

Brand: IEI Technology Pages: 165

Brand: Apex Digital Pages: 7

Brand: Acorp Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands