Texas Instruments CC2533 User Manual Download Page 252

Page: 252 / 370

Command Strobe/CSMA-CA Processor

www.ti.com

CSPSTAT (0x61E1)

–

CSP Status Register

Bit

Name

Reset

R/W

Description

7:6

—

Reserved. Read as 0

CSP_RUNNING

1: CSP is running.
0: CSP is idle.

4:0

CSP_PC

0 0000

CSP program counter

CSPX (0x61E2)

–

CSP X Register

Bit

Name

Reset

R/W

Description

7:0

CSPX

0x00

R/W

CSP X data register. Used by CSP instructions WAITX, RANDXY, INCX, DECX,
and conditional instructions

CSPY (0x61E3)

–

CSP Y Register

Bit

Name

Reset

R/W

Description

7:0

CSPY

0x00

R/W

CSP Y data register. Used by CSP instructions RANDXY, INCY, DECY, and
conditional instructions

CSPZ (0x61E4)

–

CSP Z Register

Bit

Name

Reset

R/W

Description

7:0

CSPZ

0x00

R/W

CSP Z data register. Used by CSP instructions INCZ, DECZ, and conditional
instructions

CSPT (0x61E5)

–

CSP T Register

Bit

Name

Reset

R/W

Description

7:0

CSPT

0xFF

R/W

CSP T data register. Content is decremented each time the MAC Timer
overflows while the CSP program is running. The SCP program stops when
decremented to 0. Setting CSPT = 0xFF prevents the register from being
decremented.

23.14.8 Instruction Set Summary

This section gives an overview of the instruction set. This is intended as a summary and definition of
instruction opcodes. See

Section 23.14.9

for a description of each instruction. Each instruction consists of

one byte, which is written to the

RFST

The Immediate Strobe instructions (ISxxx) are not used in a program. When these instructions are written
to the

RFST

current instruction is delayed until the immediate strobe instruction has completed.

For undefined opcodes, the behavior of the CSP is defined as a no-operation strobe command (SNOP).

252

CC253x Radio

SWRU191C

–

April 2009

–

Revised January 2012

Submit Documentation Feedback

2009

–

2012, Texas Instruments Incorporated

Summary of Contents for CC2533

































































































































































































































































































































































Search results

Summary of Contents for CC2533

Reviews:

Brands by name

Popular brands

Texas Instruments CC2533, User Manual

Search results

Summary of Contents for CC2533

Reviews:

Brands by name

Popular brands