Texas Instruments CC2533 User Manual Download Page 103

Page: 103 / 370

www.ti.com

DMA Memory Access

Table 8-2. DMA Configuration Data Structure (continued)

Byte

Bit

Name

Description

Offset

6:5

TMODE[1:0]

The DMA channel transfer mode

00:

Single

01:

Block

10:

Repeated single

11:

Repeated block

4:0

TRIG[4:0]

Selects one of the triggers shown in

Table 8-1

7:6

SRCINC[1:0]

Source address increment mode (after each transfer):

00:

0 bytes/words

01:

1 byte/word

10:

2 bytes/word

11:

–

1 byte/word

5:4

DESTINC[1:0]

Destination address increment mode (after each transfer):

00:

0 bytes/words

01:

1 byte/word

10:

2 bytes/words

11:

–

1 byte/word

IRQMASK

Interrupt mask for this channel.

Disable interrupt generation

Enable interrupt generation on DMA channel done

Mode of 8th bit for VLEN transfer length; only applicable when WORDSIZE = 0 and VLEN
differs from 000 and 111.

Use all 8 bits for transfer count

Use 7 LSB for transfer count

1:0

PRIORITY[1:0]

The DMA channel priority:

00:

Low, CPU has priority.

01:

Assured, DMA at least every second try

10:

High, DMA has priority

11:

Reserved

103

SWRU191C

–

April 2009

–

Revised January 2012

DMA Controller

Submit Documentation Feedback

2009

–

2012, Texas Instruments Incorporated

Summary of Contents for CC2533

































































































































































































































































































































































Search results

Summary of Contents for CC2533

Reviews:

Brands by name

Popular brands

Texas Instruments CC2533, User Manual

Search results

Summary of Contents for CC2533

Reviews:

Brands by name

Popular brands