manualshive.com logo in svg

Texas Instruments CC2533, User Manual

Share
Download
Texas Instruments CC2533 User Manual Download Page 126

8-Bit Timer Counter

www.ti.com

10.1 8-Bit Timer Counter

All timer functions are based on the main 8-bit counter found in Timer 3 and Timer 4. The counter
increments or decrements at each active clock edge. The period of the active clock edges, as defined by
the register bits

CLKCONCMD.TICKSPD[2:0]

, is further multiplied (the frequency is divided) by the

prescaler value set by

TxCTL.DIV[2:0]

(where x refers to the timer number, 3 or 4). The counter

operates as either a free-running counter, a down counter, a modulo counter, or an up/down counter.

It is possible to read the 8-bit counter value through the SFR register

TxCNT

, where x refers to the timer

number, 3 or 4.

The possibility to clear and halt the counter is given with

TxCTL

control register settings. The counter is

started when a 1 is written to

TxCTL.START

. If a 0 is written to

TxCTL.START

, the counter halts at its

present value.

10.2 Timer 3/Timer 4 Mode Control

In general, the control register

TxCTL

is used to control the timer operation.

10.2.1 Free-Running Mode

In the free-running mode of operation, the counter starts from 0x00 and increments at each active clock
edge. When the counter reaches 0xFF, the counter is loaded with 0x00 and continues incrementing its
value. When the terminal count value 0xFF is reached (i.e., an overflow occurs), the interrupt flag

TIMIF.TxOVFIF

is set. An interrupt request is generated if enabled, see

Section 10.6

for details. The

free-running mode can be used to generate independent time intervals and output-signal frequencies.

10.2.2 Down Mode

In the down mode, after the timer has been started, the counter is loaded with the contents in

TxCC0

. The

counter then counts down to 0x00. The interrupt flag

TIMIF.TxOVFIF

is set when 0x00 is reached. An

interrupt request is generated if enabled, see

Section 10.6

for details. The timer down mode can generally

be used in applications where an event timeout interval is required.

10.2.3 Modulo Mode

When the timer operates in modulo mode, the 8-bit counter starts at 0x00 and increments at each active
clock edge. After the count has reached the period value held in register

TxCC0,

the counter is reset to

0x00 and continues to increment. If the timer started with a value above

TxCC0

, the interrupt flag

TIMIF.TxOVFIF

is set when the terminal value (0xFF) is reached, after which the counter wraps to 0x00.

An interrupt request is generated if enabled, see

Section 10.6

for details. If a periodic interrupt is wanted

at the period value, this can be obtained by enabling an output compare interrupt on channel 0, as
explained in

Section 10.5

. The modulo mode can be used for applications where a period other than 0xFF

is required.

10.2.4 Up/Down Mode

In the up/down timer mode, the counter repeatedly starts from 0x00 and counts up until the value held in

TxCC0

is reached, and then the counter counts down until 0x00 is reached. This timer mode is used when

symmetrical output pulses are required with a period other than 0xFF, allowing implementation of
center-aligned PWM output applications. The interrupt flag

TIMIF.TxOVFIF

is set when the counter value

reaches 0x00 in the up/down mode. An interrupt request is generated if enabled, see

Section 10.6

for

details.

Clearing the counter by writing to

TxCTL.CLR

also resets the count direction to the count-up-from-0x00

mode.

10.3 Channel Mode Control

The channel modes for each channel, 0 and 1, are set by the control and status registers

TxCCTLn,

where n is the channel number, 0 or 1. The settings include capture and compare modes.

126

Timer 3 and Timer 4 (8-Bit Timers)

SWRU191C

–

April 2009

–

Revised January 2012

Submit Documentation Feedback

Copyright

©

2009

–

2012, Texas Instruments Incorporated

Summary of Contents for CC2533



















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands