Teseq NSG 3040 User Manual Download Page 105

Page: 105 / 156

105

Thermal monitoring of internal backfilter chokes; in case the EUT current

goes up, the integrated fans, which are still in standby mode and at low
EUT currents, will speed up to improve cooling.

In case of intentional or unintentional overloading, the CDN 3043 and 3063

series will automatically switch off EUT power, in order to protect itself
(risk of fire)

Slow Damped Oscillatory Wave immunity testing of 3-Phase equipment needs
a dedicated 3-Phase CDN. Please check your Teseq equipment supplier for
availability.

14.2.1 CDN 3043 - 32 A series

Technical specifications:

NSG 3040 on top of CDN 3043

Voltage ratings:

280 VAC - phase to neutral or phase to ground

480 VAC - phase(s) to phase(s)

up to 125 VDC - full current range

up to 225 VDC - for max. 7 A

Summary of Contents for NSG 3040





























































































































































Search results

Summary of Contents for NSG 3040

Reviews:

Related manuals for NSG 3040

Brands by name

Popular brands

Teseq NSG 3040, User Manual

Search results

Summary of Contents for NSG 3040

Reviews:

Related manuals for NSG 3040

Brands by name

Popular brands