Teseq NSG 3040 User Manual Download Page 52 | Manualshive

Page: 52 / 156

background image

52

NSG 3040 EMC test system

Load user test window

8.2 The bottom bar
8.2.1 LOAD USER TEST

Touch the “Load User Test” button to display a list of all test files that have
been created and saved by the user. Only files for the selected test type are
displayed. The Figure below shows the load user test window with several burst
tests displayed.

The user can scroll through the tests by touching the “UP” and “DOWN” arrows
on the right side of the screen to scroll through the tests.

Touch the button to the left of the test name to select it. A red border is dis-
played around the selected test.

Touch the “OK” button to load the test and return to the test parameter window.

Touch the “Delete” button to delete a saved test. A window asking the user to
confirm or cancel this action will be displayed. Touch “OK” to delete the file, or
“Cancel” to cancel this action.

NOTE:

Once a test has been deleted it cannot be restored.

«
...
50
51
52
53
54
...
»

Summary of Contents for NSG 3040





























































































































































Reviews:

No comments

Related manuals for NSG 3040

Brand: HANYOUNG NUX Pages: 2

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 30

Brand: Yamaha Pages: 30

EF4500iSE - Inverter Generator

Brand: Yamaha Pages: 10

Brand: B&B Electronics Pages: 13

Brand: Linear Technology Pages: 6

Brand: Optical Systems Pages: 2

GlobeTrotter Ex GE 0003

Brand: Option Audio Pages: 4

VideoExpress Converter

Brand: Miglia Pages: 12

Brand: 2N Pages: 17

Brand: Motrona Pages: 28

Brand: RS Pages: 8

Brand: MDS Power Pages: 16

Brand: Black Box Pages: 18

Brand: AMV ELECTRONICA Pages: 23

RI-ENERGYFLOW-3P-15 Series

Brand: Rayleigh Instruments Pages: 24

Brand: SAJ Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands