Teseq NSG 3040 User Manual Download Page 28 | Manualshive

Page: 28 / 156

background image

28

NSG 3040 EMC test system

6.2.1 Instrument supply

This input is to power the instrument.

NOTE - Do not confuse the Mains power input with the
EUT power input.

This input contains the fuses and the instrument ON/OFF switch.

WARNING - Before operating the NSG 3040, make sure
that the voltage shown on the mains input module cor-
responds with the voltage of the local supply to which
the instrument will be connected, and that the fuses
are correctly rated (2 x 3.15 AT).

EUT power input

Instrument supply

System interface

Ethernet connection

6.1.6 Touch screen and user interface

The color 7” touch screen display controls include a wheel and 3 sensitivity keys
used to 1, 10 or 100 steps per wheel click. The Start, Stop, and Pause keys are
used to control the procedure.

All user interface function menus and sub-menus are described in “The stan-
dard user interface SUI”.

6.2 Rear panel

«
...
26
27
28
29
30
...
»

Summary of Contents for NSG 3040





























































































































































Reviews:

No comments

Related manuals for NSG 3040

OTEC IEWQ Series

Brand: Omega Pages: 29

Brand: Grape Solar Pages: 2

Automotive Ethernet Converter

Brand: X2E Pages: 22

Brand: Barco Pages: 2

Brand: D&H Pages: 106

Brand: UNICOM Pages: 6

Brand: Peak Pages: 28

SF1.6/2.2/3KTL-S

Brand: Moso Pages: 38

Brand: SMA Pages: 56

Brand: Pro-Ject Audio Systems Pages: 3

Brand: SMA Pages: 48

Brand: Felicitysolar Pages: 17

Brand: Zapi Pages: 66

Brand: Qcells Pages: 80

Brand: Patton electronics Pages: 9

miConverter GX/T

Brand: Omnitron Systems Technology Pages: 2

Brand: KTI Networks Pages: 47

Brand: Bosch Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands