Terberg OmniDEL Original Instructions Manual Download Page 9

Page: 9 / 37

3. Transport and storage

3.1 General

- Check the position of the centre of gravity of the bin lift when raising this with a forklift truck or tackle.

- When dismantling disconnect the bin lift from the vehicle using the plugs and quick release couplings intended

for this purpose.

- Protect the 16-pole connecting plugs from water.
- Connect the hydraulic couplings together.
- Weight:

Omni

DEL

595 kg (depending on configuration)

Omni

DEL e

655 kg (depending on configuration)

- Use a mobile hoist with minimum lifting capacity of 1000 kg and a hoist beam.
- Raise the bin lift using the lifting points provided.
- Lay the bin lift flat on the ground.

Terberg Machines B.V. IJsselstein, The Netherlands

electronically, mechanically, by print, photoprint, microfilm or any other means without prior written permission from the publisher.

Min. 1000 kg

1961

Summary of Contents for OmniDEL






































Search results

Summary of Contents for OmniDEL

Reviews:

Related manuals for OmniDEL

Brands by name

Popular brands

Terberg OmniDEL, Original Instructions Manual

Search results

Summary of Contents for OmniDEL

Reviews:

Related manuals for OmniDEL

Brands by name

Popular brands