background image

36

ã

Terberg Machines B.V. IJsselstein, The Netherlands

All rights reserved. No part of this book may be reproduced, stored in database or retrieval system, or published, in any form or in any way, 

electronically, mechanically, by print, photoprint, microfilm or any other means without prior written permission from the publisher.

5.12.3  Resetting the emergency stop

- Reset the emergency stop (pull out the emergency stop button); the buzzer in the cabin will stop. 

Resetting of the compaction body may be required, consult body manual for correct procedure.

- Press the DOWN button; the lifting chair lowers to the lowest position.

- Investigate the reason for pressing the emergency stop button.
- Remove the bin/container from the bin lift system if applicable.
- The bin lift system is ready for use again.

5.12.4  Becoming trapped

In the event of a dangerous occurance or if a person has become trapped in the lifting mechanism and an
emergency stop button has been pressed, the system will need to be reset to allow the chairs to be raised or
lowered which ever is appropriate to release the person.
An understanding of the resetting procedure of the compaction body will be required of the operators.

In such cases act as follows:

-

Reset the emergency stop button.

- Use the dark blue DOWN button to allow the lifting chairs to lower or the light blue UP button to allow the

lifting chairs to raise.

Summary of Contents for OmniDEL






































Reviews: