Terasic Apollo S10 User Manual Download

Page: 77 / 96

Apoolo-S10
User Manual

www.terasic.com

March 31, 2020

Figure 3-5 Top File Type in the System Builder window



System Configuration

Users are given the flexibility of enabling their choices of components connected to the

FPGA under System Configuration, as shown in

Figure 3-6

. Each component of the

FPGA board is listed to be enabled or disabled according to users’ needs. If a

component is enabled, the System Builder will automatically generate the associated

pin assignments including its pin name, pin location, pin direction, and I/O standards.

Note:

The pin assignments for some components (e.g. DDR4) require associated

controller codes in the Quartus project or it would result in compilation error. Hence

please do not select them if they are not needed in the design. To use the DDR4

controller, please refer to the DDR4 SDRAM demonstration in Chapter

Summary of Contents for Apollo S10

































































































Search results

Summary of Contents for Apollo S10

Reviews:

Related manuals for Apollo S10

Brands by name

Popular brands

Terasic Apollo S10, User Manual

Search results

Summary of Contents for Apollo S10

Reviews:

Related manuals for Apollo S10

Brands by name

Popular brands