manualshive.com logo in svg

Teledyne 300E, Instruction Manual, Page: 199 / 253

Share
Download
Teledyne 300E Instruction Manual Download Page 199

Model 300E Carbon Monoxide Analyzer 
Instruction Manual 

TROUBLESHOOTING & REPAIR PROCEDURES 

 

P/N 04288 REV: A 

 

199 

 

§ 

Failed Sync/Demod Board 

§ 

Faulty Connectors/Wiring 

 

11.2. Gas Flow Problems 

In general, flow problems can be divided into three categories: 

1. 

Flow is too high 

2. 

Flow is greater than zero, but is too low, and/or unstable 

3. 

Flow is zero (no flow) 

When troubleshooting flow problems, it is a good idea to first confirm that the 

actual flow and not the analyzer’s flow sensor and software are in error, or the flow 
meter is in error. Use an independent flow meter to perform a Flow Check as 

described in Section 9.4.  If this test shows the flow to be correct, check the 
Pressure sensors as described in Section 10.8.10. 

11.2.1. 

Typical Flow Problems 

11.2.1.1. Flow is Zero 

The unit displays a 

SAMPLE FLOW 

warning message on the Front Panel Display or 

the 

SAMPLE FLOW 

Test Function reports a zero or very low flow rate. 

Confirm that the sample pump is operating (turning).  If not, use an AC Voltmeter 

to make sure that power is being supplied to the pump.  If no power is present at 
the electrical leads of the pump see Section 11.5. 

If AC power is being supplied to the pump, but it is not turning, replace the pump.   

If the pump is operating but the unit reports no gas flow, perform a Flow Check as 

described in Section 9.4.2. 

If no independent flow meter is available: 

§ 

Disconnect the gas lines from both the Sample inlet and the Exhaust outlet on 

the Rear Panel of the instrument.   

§ 

Make sure that the unit is in basic SAMPLE Mode.  

§ 

Place a finger over an Exhaust outlet on the rear panel of the instrument.   

§ 

If gas is flowing through the analyzer, you will feel pulses of air being 
expelled from the Exhaust outlet.  

Summary of Contents for 300E






























































































































































































































































Reviews:

No comments