manualshive.com logo in svg

Teledyne 2120XL, Operating Instructions Manual, Page: 84 / 85

Share
Download
Teledyne 2120XL Operating Instructions Manual Download Page 84

Appendix Model 

2120XL 

 

 

Teledyne Analytical Instruments 

72 

 

 

Digital Inputs:   Two digital inputs for remote span and 

zero 

 

Weight:  35 lbs (15.9 kg) 

A.2 Recommended Replacement Parts List 

 

Qty. Part 

Number 

Description 

1 

C75825A 

Main PCB w/o EPROM 

1 C84447A  Amplifier 

PCB 

1 

C84132A 

Back Panel Power Supply PCB 

1 

C84129A 

Front  Panel Display PCB 

1 

S01748-120 

Scrubber of N2 Gas for zero cal. (120 V)  

  

-OR- 

1 

S01748-240 

Scrubber of N2 Gas for zero cal. (240 V) 

1 

F2374 

Flow Control Module 

1 

A85552 

2120XL std. EPROM for Main PCB 

Note:  Orders for replacement parts should include the part 

number (if available) and the model and serial number of 
the instrument for which the parts are intended. 

Orders should be sent to: 

 

TELEDYNE ANALYTICAL INSTRUMENTS

 

 
16830 Chestnut Street 
City of Industry, CA 91748 
Telephone: (626) 934-1500 
Fax: (626) 961-2538  
Web: www.teledyne-ai.com 
or your local representative. 
 
 
 

Summary of Contents for 2120XL






















































































Reviews:

No comments