manualshive.com logo in svg

Teledyne 2120XL, Operating Instructions Manual, Page: 48 / 85

Share
Download
Teledyne 2120XL Operating Instructions Manual Download Page 48

Operation Model 

2120XL 

 

 

Teledyne Analytical Instruments 

36 

 

4.1 Powering Up the Analyzer 

CAUTION: 

OZONE EMISSIONS ARE POSSIBLE IF AIR OR 
MOISTURE ARE IONIZED IN THE SAMPLING 
SYSTEM. THE SAMPLE PATH MUST BE 
RELATIVELY FREE OF AIR AND/OR MOISTURE 
BEFORE APPLYING THE IONIZING VOLTAGE.  
 
KEEP THE POWER OFF UNTIL THE ANALYZER IS 
FULLY PURGED. 

1.

 

Purge the analyzer and sampling system using the procedure 
described in Section 3.7. 

2.

 

Connect the power cord to the proper power source for your 
analyzer. The analyzer will begin its power up sequence 

CAUTION: 

EQUIPMENT DAMAGE MAY RESULT IF THE 
ANALYTICAL CELL IN THIS UNIT IS EXPOSED TO 
EXCESSIVE PRESSURE, CAUSING IT TO BREAK OR 
SHATTER.  
 

3.

 

Observe the display while allowing the instrument to warm 
up and the readings stabilize. Drift occurs until internal 
temperatures stabilize and the analytical cell is completely 
purged. A persistent drift indicates an improperly purged 
system or an air leak into the system. 

4.2 Zero and Span Calibration 

The Model 2120XL is designed to provide a linear response over 

the 0-100 ppm concentration range for nitrogen in argon. Therefore, a 
two-point (zero and span) calibration is sufficient to define the 
calibration curve for this analyzer. 

Prior to shipment, the analyzer was calibrated and linearized at the 

factory in accordance with the calibration data shipped with your 
analyzer. Use these settings to verify that the unit is in calibration, or re-
calibrate the analyzer as outlined in Section 4.5.2. Recalibrations are 
required periodically. The user can also redefine the linearization curve 
for this instrument. Refer to Section 4.5.1.12.  

 

 

Summary of Contents for 2120XL






















































































Reviews:

No comments