Teledyne 2120XL Operating Instructions Manual Download Page 5 | Manualshive

Page: 5 / 85

Teledyne 2120XL Operating Instructions Manual Download Page 5

Trace Nitrogen in Argon Analyzer

Teledyne Analytical Instruments

v

CAUTION:

THE ANALYZER SHOULD ONLY BE USED ONLY
FOR THE PURPOSE AND IN THE MANNER
DESCRIBED IN THIS MANUAL.

IF YOU USE THE ANALYZER IN A MANNER OTHER
THAN THAT FOR WHICH IT WAS INTENDED,
UNPREDICTABLE BEHAVIOR COULD RESULT
POSSIBLY ACCOMPANIED WITH HAZARDOUS
CONSEQUENCES.

This manual provides information designed to guide you through

the installation, calibration operation and maintenance of your new
analyzer. Please read this manual and keep it available.

Occasionally, some instruments are customized for a particular

application or features and/or options added per customer requests.
Please check the front of this manual for any additional information in
the form of an Addendum which discusses specific information,
procedures, cautions and warnings that may be peculiar to your
instrument.

Manuals do get lost. Additional manuals can be obtained from

Teledyne at the address given in the Appendix. Some of our manuals are
available in electronic form via the internet. Please visit our website at:
www.teledyne-ai.com.

«
...
3
4
5
6
7
...
»

Summary of Contents for 2120XL






















































































Reviews:

No comments