manualshive.com logo in svg

Teledyne 2120XL, Operating Instructions Manual, Page: 15 / 85

Share
Download
Teledyne 2120XL Operating Instructions Manual Download Page 15

Trace Nitrogen in Argon Analyzer 

Introduction 

 Teledyne 

Analytical 

Instruments 

3

 

 

 

Extensive self-diagnostic testing, at startup and on demand, 
with continuous power-supply monitoring. 

 

Two way RFI protection. 

 

RS-232 serial digital port for use with a computer or other 
digital communication device. 

 

Four analog outputs: two for measurement (0–1 VDC and 
isolated 4–20 mA DC) and two for range identification. 

 

Convenient and versatile, steel, flush-panel or rack-
mountable case with slide-out electronics drawer. 

 

1.4 Front Panel  

Operator controls and displays are located on the front panel as 

shown in Figure 1-1.  

 

Figure 1-1 Model 2120XL Front Panel 

The standard 2120XL Nitrogen in Argon Analyzer is panel 

mounted designed for easy installation in a standard 19” instrument 
rack. All user controls and displays accessible from the front panel.  

The front panel has thirteen buttons for operating the analyzer, a 

digital meter, and an alphanumeric vacuum fluorescent (VFD) display. 

Summary of Contents for 2120XL






















































































Reviews:

No comments