manualshive.com logo in svg

Teledyne 2120XL, Operating Instructions Manual, Page: 32 / 85

Share
Download
Teledyne 2120XL Operating Instructions Manual Download Page 32

Installation Model 

2120XL 

 

 

Teledyne Analytical Instruments 

20 

 

3.5 Electrical Connections 

Electrical Connections are made at the rear of the instrument. See 

Figure 3-2. 

For safe connections, no uninsulated wiring should be able to come 

in contact with fingers, tools or clothing during normal operation. 

CAUTION: 

USE SHIELDED CABLES. ALSO, USE PLUGS THAT 
PROVIDE EXCELLENT EMI/RFI PROTECTION. THE 
PLUG CASE MUST BE CONNECTED TO THE CABLE 
SHIELD, AND IT MUST BE TIGHTLY FASTENED TO 
THE ANALYZER WITH ITS FASTENING SCREWS. 
ULTIMATELY, IT IS THE INSTALLER WHO ENSURES 
THAT THE CONNECTIONS PROVIDE ADEQUATE 
EMI/RFI SIELDING. 

3.5.1 Primary Input Power 

The power cord receptacle and fuse block are located in the same 

assembly. Insert the power cord into the power cord receptacle. 

CAUTION: 

POWER IS APPLIED TO THE INSTRUMENT'S 
CIRCUITRY AS LONG AS THE INSTRUMENT IS 
CONNECTED TO THE POWER SOURCE. 
THESTANDBY SWITCH ON THE FRONT PANEL IS 
FOR SWITCHING POWER ON OR OFF TO THE 
DISPLAYS AND OUTPUTS ONLY. 

The universal power supply requires an 85–250 VAC, 47-63 Hz 

power source. 

Fuse Installation:

 The fuse block, at the right of the power cord 

receptacle, accepts US or European size fuses. A jumper replaces the 
fuse in whichever fuse receptacle is not used. Fuses are not installed at 
the factory. Be sure to install the proper fuse as part of installation. (See 

Fuse Replacement

 in Chapter 5, 

Maintenance

.) 

3.5.2 50-Pin Equipment Interface Connector  

Figure 3-3 shows the pin layout of the Equipment Interface 

Connector. The arrangement is shown as seen when the viewer faces the 
rear panel of the analyzer. The pin numbers for each input/output 
function are given where each function is described in the paragraphs 
below. 

 

 

Summary of Contents for 2120XL






















































































Reviews:

No comments