Teledyne 2120XL Operating Instructions Manual Download Page 70

Page: 70 / 85

Operation Model

2120XL

Teledyne Analytical Instruments

After pressing the SPAN button, the mode selection screen appears:

Select Span

Mode : Manual (Auto)

where Manual and Automatic can be toggled back and forth using the

▲

▼

arrow keys. Once the proper mode is displayed, press ENTER.

The following screen appears:

Span

100.0

<ENT> to begin Span

This screen allows the user to input the known concentration of the

span gas used. Uuse the

▲

▼

arrow keys to enter the span gas

concentration. Press ENTER when finished.

4.5.2.3.1 Manual Span

If manual span mode was selected, the following screen appears:

39.25

<ENT> to Finish

In the Manual Mode, the user has the opportunity to decide when

the span settling is close enough to the actual concentration to be valid.
When the value is sufficiently close to the known concentration and
sufficiently stable, press ENTER to accept the span calibration.

4.5.2.3.2 Auto Mode Span

If AUTO mode was selected from the Span Mode Selection screen

the following screen appears:

Span Settling:

0:58

The time value displayed at the right count down to zero from the

value currently held in Calholdtimer. See Section 4.5.1.9.

When the counter reaches zero, the display switches to display the

live adc change count.

Summary of Contents for 2120XL






















































































Search results

Summary of Contents for 2120XL

Reviews:

Teledyne 2120XL, Operating Instructions Manual, Page: 70 / 85

Search results

Summary of Contents for 2120XL

Reviews: