Teledyne 2120XL Operating Instructions Manual Download Page 62

Page: 62 / 85

Operation Model

2120XL

Teledyne Analytical Instruments

When

HOLD

is selected, the analog output (4-20 mA) and the

range ID contacts will freeze on their last state before entering one of the
calibration modes. When the instrument returns to the

Analyze

mode,

either by a successful or an aborted calibration, there will be a three-
minute delay before the analog outputs and the range ID contacts start
tracking again.

The concentration alarms freeze on their last state before entering

calibration regardless of selecting

HOLD

TRACK

. But, when

HOLD

is selected the concentration alarms will remain frozen for the time set in
the

Calholdtimer

screen after the analyzer returns to the

Analyze

mode.

See Section 4.5.1.9

Calibration Hold Timer

4.5.1.9

ALIBRATION

OLD

IMER

ALHOLDTIMER

)

This function sets the time period for the analog output hold as well

as the time period for which the alarms will be suppressed during a
calibration event.

To set the time period for a hold, press the

SYSTEM

key to display

the first System menu. Use the

◄►

arrow keys to position the blinking

over the

function, and press ENTER. A second screen of system

function will appear. Use the

◄►

arrow keys to position the blinking

over the

Calholdtimer

function, and press ENTER to advance to the

Calholdtimer

screen.

Calbrt hold:

1 min

Sample hold:

1 min

The time intervals can be set from 0 (off) to 100 minutes using the

▲

▼

arrow keys. Press ENTER when the desired value is displayed.

The factory default is three minutes, but the delay time is program-

mable. This preference is stored in non-volatile memory so that it is
recovered if power is removed from the instrument.

4.5.1.10

ODEL

CREEN

The Model screen displays the manufacturer, model, and software

version information for your analyzer.

To view the information in the Model function, press the

SYSTEM

key to display the first System menu. Use the

◄►

arrow keys to

position the blinking over the

function, and press ENTER. Repeat

Summary of Contents for 2120XL






















































































Search results

Summary of Contents for 2120XL

Reviews:

Teledyne 2120XL, Operating Instructions Manual, Page: 62 / 85

Search results

Summary of Contents for 2120XL

Reviews: