manualshive.com logo in svg

Teledyne 2120XL, Operating Instructions Manual, Page: 39 / 85

Share
Download
Teledyne 2120XL Operating Instructions Manual Download Page 39

Trace Nitrogen in Argon Analyzer  

Installation 

 

 

 

Teledyne Analytical Instruments 

27 

az

<enter> 

Immediately starts an autozero. 

st

<enter> 

Toggling input. Stops/Starts any 
status message output from the 
RS-232, until 

st

<enter> is sent 

again. 

 
The RS-232 protocol allows some flexibility in its implementation. 

Table 3-6 lists certain RS-232 values that are required by the Model 
2120XL implementation. 

Table 3-6: Required RS-232 Options 

 

Parameter Setting 

  

Baud  9600 

  

Byte  8 

bits 

  

Parity  none 

  Stop 

Bits  1 

 

Message Interval 

2 seconds. When CRC opens 
again, zero and span are done, 
and the sample is being analyzed. 

3.6 Gas Connections

 

CAUTION: 

THIS INSTRUMENT IS NOT DESIGNED TO HANDLE 
HAZARDOUS GASES.  

OZONE EMISSIONS CAN OCCUR IF AIR OR 
MOISTURE ARE IONIZED IN THE SAMPLING 
SYSTEM. THE SAMPLE PATH MUST BE 
RELATIVELY FREE OF AIR AND/OR MOISTURE 
BEFORE APPLYING THE IONIZING VOLTAGE. 
 
KEEP THE MODEL 2120XL POWER OFF AND PURGE 
THE EXTERNAL TUBING. THEN APPLY POWER  TO 
PURGE THE INTERNAL LINES. ANALYZER POWER 
IS NEEDED TO PURGE ANALYZER SINCE THE 
FLOW CONTROL MODULE NEEDS POWER TO 
OPERATE. MAKE SURE THAT THE VENT IS AT 
ATMOSPHERIC PRESSURE. 

 

Summary of Contents for 2120XL






















































































Reviews:

No comments