Tektronix TLA7000 Series Installation Manual Download Page 65 | Manualshive

Page: 65 / 121

background image

Basic Installation

Figure 43: TLA7016 accessories connections

Additional Accessory

Connection Information

Connect additional accessories as needed. (See Table 4.)

Table 4: Additional accessory connection information

Item

Description

Monitor

There are two display ports on the TLA7012: Primary (DVI-D, digital output only), and Secondary (DVI-I,
digital/analog out). Simulscan mode displays the same information on the internal display and the
external monitor connected to either Primary or Secondary.
To change the display settings, right-click the mouse on the desktop, select Properties, and go to the
Settings tab. Select the settings for your monitor. Note that some of the display settings may not
function until you connect an external monitor.
Use the VGA-to-DVI display adapter to connect a VGA monitor to the Secondary DVI-D output. Part
numbers for accessories and options are listed at the end of this manual. (See page 93,

Accessories &

Options

.) If you use a nonstandard monitor, you may need to change the Windows display settings to

achieve the proper resolution.

LAN

Connect the mainframes to your network through the Gbit LAN connectors. You can remotely control
the mainframes through a LAN switch using your PC (loaded with the TLA application software), or the
dedicated PC controller (TLA7PC1).

Printer

The instruments send printer information to the USB ports. Use any of the four USB ports for your printer.

TLA7000 Series Logic Analyzers Installation Manual

47

«
...
63
64
65
66
67
...
»

Summary of Contents for TLA7000 Series


























































































































Reviews:

No comments

Related manuals for TLA7000 Series

Brand: Atomos Pages: 4

Brand: Campbell Pages: 362

Brand: Campbell Pages: 60

Brand: Campbell Pages: 116

Brand: Campbell Pages: 30

Brand: Campbell Pages: 55

Brand: Keithley Pages: 32

CellaCast PA8 Series

Brand: Keller Pages: 12

Brand: Hach Pages: 96

Brand: Teledyne Hastings Instruments Pages: 54

AccuPoint 2 ATP

Brand: Neogen Corporation Pages: 16

HydroTracer FLV

Brand: aboni Pages: 48

Brand: Lutron Electronics Pages: 43

Brand: Hanna Instruments Pages: 25

WTW SensoLyt 900

Brand: Xylem Pages: 12

Brand: NetThings Pages: 3

Brand: GARO Pages: 15

Brand: Mountz Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands