manualshive.com logo in svg

Tektronix TLA7000 Series, Installation Manual

Share
Download
Tektronix TLA7000 Series Installation Manual Download Page 98

Restoring and Reinstalling Software

1.

Note which of the modules that may require new

fi

rmware.

If any modules are missing from the System window, you can verify the status
of the modules by doing the following steps:

a.

Select System Properties in the System menu.

b.

Click the Modules tab.

c.

Note the information under the Messages column for any installed
modules. If any modules indicate invalid or similar messages, you must
update the

fi

rmware for those modules.

2.

Turn off the logic analyzer and disconnect the power cord.

3.

Remove the modules from the logic analyzer.

4.

Locate the

fl

ash programming pins on the rear of each module. (See Figure 59

on page 81.)

5.

Install a jumper on the

fl

ash programming pins (use one of the spare jumpers

that came with your logic analyzer).

6.

Reinstall the module(s) in the logic analyzer.

7.

Reconnect the power cord and then power on the logic analyzer.

8.

Wait for the TLA application to start.

NOTE.

Any modules with the

fl

ash programming jumper installed will not display

in the System window.

9.

Exit the TLA application (and pattern generator application if you have it
installed on your instrument).

80

TLA7000 Series Logic Analyzers Installation Manual

Summary of Contents for TLA7000 Series


























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands