Tektronix TLA7000 Series Installation Manual Download Page 83

Page: 83 / 121

Merging Modules

Figure 53: Feeding the merge cable through the cover

10.

Turn the merge cable bracket over so that the guide pins point up.

11.

Place the bracket over the merge cable connector.

12.

Install the two screws that hold the merge cable bracket in place.

CAUTION.

To prevent damage to the module during the installation process,

reinstall the cover exactly as described in steps 14 through 19.

If the cover is not properly seated, the module can be damaged when you install it
in the mainframe and it may not meet EMC requirements.

13.

Replace the logic analyzer module cover.

14.

Push forward on the cover so the tab on the front edge of the cover inserts
into the rear of the front subpanel. Make sure that the cover is fully seated
(no gaps) against the front and rear chassis

anges.

TLA7000 Series Logic Analyzers Installation Manual

Summary of Contents for TLA7000 Series


























































































































Search results

Summary of Contents for TLA7000 Series

Reviews:

Related manuals for TLA7000 Series

Brands by name

Popular brands

Tektronix TLA7000 Series, Installation Manual

Search results

Summary of Contents for TLA7000 Series

Reviews:

Related manuals for TLA7000 Series

Brands by name

Popular brands