Taylor 810 Series Original Service Instructions Download | Manualshive

Page: 9 / 208

background image

INTRODUCTION

1-5

Model 810, 812, 820, 822, 828 Series

Introduction

1

IMPORTANT!

Supply cords used with this

machine shall be oil-resistant, sheathed flexible cable,
not lighter than ordinary polychloroprene or other
equivalent synthetic elastomer-sheathed cord (code
designation 60245 IEC 57). They must be installed with
the proper cord anchorage to relieve conductors from
strain, including twisting, at the terminals and protect the
insulation of the conductors from abrasion.

DANGER!

The main power supply(s) must be

disconnected prior to performing any repairs. Failure to
follow this instruction may result in personal injury or
death from electrical shock or hazardous moving parts as
well as poor performance or damage to the equipment.

Note:

Grills require electrical power for operation. In the

event of a power outage, place the machine in the OFF
position.

WARNING!

This machine must

NOT

be

installed in an area where a water jet or hose can be
used.

NEVER

use a water jet or hose to rinse or clean

this machine. Using a water jet or hose on or around this
equipment may result in the electrocution of the user or
damage to the equipment.

Ventilation and Clearance

To ensure proper operation of this machine, it must be
installed away from all combustible products.

CAUTION!

Allow for proper clearance and

airflow. Failure to comply may result in poor performance,
damage to the machine and create an unsafe operating
condition.

CAUTION!

After setup, do not store anything

on top of the grill. Failure to follow this instruction may
result in a fire hazard.

WARNING!

This machine must be isolated

from all combustible construction and materials including
but not limited to walls, partitions, furniture, floors,
curtains, paper, boxes, and decorations. Failure to
comply may result in fire and cause destruction and
severe injury.

Grease Disposal Container

In order to comply with NSF Standard 4 requirements, an
appropriate grease disposal container must be provided.
This container is supplied by the KES, not the Taylor
Company.

Environmental Notices

IMPORTANT!

If the crossed-out waste

container symbol is affixed to this machine, it signifies
that this machine is compliant with the EU Directive as
well as other similar legislation in effect after August 13,
2005. Therefore, it must be collected separately after its
use is completed and cannot be disposed as unsorted
municipal waste. The user is responsible for delivering
the product to the appropriate collection facility, as
specified by your local code.

«
...
7
8
9
10
11
...
»

Summary of Contents for 810 Series

















































































































































































































Reviews:

No comments

Related manuals for 810 Series

Brand: GardenGrill Pages: 65

Brand: Parkside Pages: 49

GR2297802-MM-00

Brand: Rankam Pages: 52

Brand: Barbecook Pages: 128

Brand: Cadac Pages: 6

Brand: Metabo Pages: 64

Brand: Nostalgia Electrics Pages: 30

Brand: T-Fal Pages: 24

Brand: EINHELL Pages: 12

Brand: Nexgrill Pages: 71

Brand: HELLRAZR Pages: 32

Brand: Quadro Pages: 16

Brand: Gourmia Pages: 20

Brand: SEVERIN Pages: 88

Brand: Black & Decker Pages: 8

Kamado CM155-024

Brand: Charmate Pages: 8

Brand: Hitachi Pages: 58

Brand: GEORGE Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands