manualshive.com logo in svg

TATA Motors Punch 2021, Owner'S Manual

Share
Download
TATA Motors Punch 2021 Owner'S Manual Download Page 167

 

 

Screw the bottle clockwise firmly 

4.

against the slight resistance of the 
notches onto the sealing gasket of the 
bottle connector until it is screwed 
tight. 

Remove the valve cap from the dam-

5.

aged tire. Pull the protective cap off the 
end of the hose and screw the hose 
firmly onto the valve of the damaged 
tire. Make sure that the compressor 
switch is switched to “0” and the pres-
sure “air release” valve is closed. 

Insert power plug into the 12 volt 

6.

power socket connection. 

Start the engine (only if the vehicle is 

7.

outdoors or in a well ventilated area). 

 

 

Press compressor switch to “I”. 

8.

 

 

 
 

 

 

Inflate the tire within about 10 minutes 

9.

to an inflation pressure of minimum 
180 kPa, (1.8 bar, and 26   psi) and a 
maximum of 300 kPa (3 bar, 43 psi). 

Switch off the compressor briefly in 

10.

order to read the actual tire pressure 
from the pressure gauge. 

 

 

Leave the bottle seal intact. Screwing 
the bottle onto the bottle holder will 
pierce the seal of the bottle. Avoid skin 
contact with the sealant which contains 
natural rubber latex. Do not open pres-
sure “air release” valve. Please use pro-
tective glove for safety purpose.

 WARNING

Asphyxiation may occur if the engine is 
allowed to run in a non-ventilated or 
poorly ventilated area (e.g. inside a 
building)

 NOTE

Check the sidewall of the tire prior to in-
flation. If there are any cracks, bumps 
or similar damage, do not attempt to in-
flate the tire. Do not stand directly be-
side the tire while the compressor is 
pumping. Watch the sidewall of the tire. 
If any cracks, bumps or similar damage 
appear, turn off the compressor and let 
the air out by means of the pressure “air 
release” valve. In this case, do not con-
tinue to use the tire.

 NOTE

When pumping in the sealant through 
the tire valve, the pressure may rise up 
to 500 kPa (5 bar, 73 psi) but will drop 
again after about 30 seconds.

 WARNING

 WARNING

If heavy vibrations, unsteady steering 
behavior or noises should occur while 
driving, reduce your speed and drive 
with caution to a place where it is safe 
for you to stop the vehicle. Recheck the 
tire and its pressure. If the tire pressure 
is less than 130 kPa (1.3 bar, 19 psi) or 
if there are any visible cracks, bumps or 
similar damage on the side wall, do not 
continue to use the tire!

EMERGENCY AND BREAKDOWN ASSISTANCE

159

Summary of Contents for Punch 2021















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands