D14128.03—JULY 2009
60
Codec C90
System Integrator Guide
Contents
Introduction
Getting Started
Interfaces
About the API
xConfiguration
xCommand
xStatus
Cameras
Appendices
Contact us
xConfiguration NetworkServices SIP Mode:
<On/Off>
Determines whether the system should be able to place and receive SIP calls.
On: Set to On to enable the possibility to place and receive SIP calls.This is the default setting.
Off: Set to Off to disable the possibility to place and receive SIP calls.
NOTE! Changes in this setting requires the codec to be restarted.
Example:
xConfiguration NetworkServices SIP Mode: On
xConfiguration NetworkServices SNMP CommunityName:
<S: 0, 50>
Enter the name of the Network Services SNMP Community. SNMP Community names are used to
authenticate SNMP requests. SNMP requests must have a ‘password’ (case sensitive) in order to receive a
response from the SNMP Agent in the codec. The default password is “public”. If you have the TANDBERG
Management Suite (TMS) you must make sure the same SNMP Community is configured there too. Note!
The SNMP Community password is case sensitive.
Format: String with a maximum of 50 characters.
Example:
xConfiguration NetworkServices SNMP Com munityName: “public”
xConfiguration NetworkServices SNMP Host [1..3] Address:
<S: 0, 64>
Enter the address of up to three SNMP Managers. All traps will then be sent to the hosts listed.
The system’s SNMP Agent (in the codec) responds to requests from SNMP Managers (a PC program etc.).
SNMP Traps are generated by the SNMP Agent to inform the SNMP Manager about important events. Can
be used to send event created messages to the SNMP agent about different events like: system reboot,
system dialing, system disconnecting, MCU call, packet loss etc. Traps can be sent to multiple SNMP Trap
Hosts.
Format: String with a maximum of 64 characters.
Example:
xConfiguration NetworkServices SNMP Host 1 Address: “”
xConfiguration NetworkServices SNMP Mode:
<Off/ReadOnly/ReadWrite>
SNMP (Simple Network Management Protocol) is used in network management systems to monitor
network-attached devices (routers, servers, switches, projectors, etc) for conditions that warrant
administrative attention. SNMP exposes management data in the form of variables on the managed
systems, which describe the system configuration. These variables can then be queried (set to ReadOnly)
and sometimes set (set to ReadWrite) by managing applications.
Off: Set to Off when you want to disable the SNMP network service.
ReadOnly: Set to ReadOnly when you want to enable the SNMP network service for queries only.
ReadWrite: Set to ReadOnly when you want to enable the SNMP network service for both queries and
commands.
Example:
xConfiguration NetworkServices SNMP Mode: ReadWrite
xConfiguration NetworkServices SNMP SystemContact:
<S: 0, 50>
Enter the name of the Network Services SNMP System Contact.
Format: String with a maximum of 50 characters.
Example:
xConfiguration NetworkServices SNMP SystemContact: “”
xConfiguration NetworkServices SNMP SystemLocation:
<S: 0, 50>
Enter the name of the Network Services SNMP System Location.
Format: String with a maximum of 50 characters.
Example:
xConfiguration NetworkServices SNMP SystemLocation: “”
xConfiguration NetworkServices Telnet Mode:
<On/Off>
Telnet is a network protocol used on the Internet or local area network (LAN) connections.
On: The Telnet protocol is enabled.
Off: The Telnet protocol is disabled. This is the default factory setting.
Example:
xConfiguration NetworkServices Telnet Mode: Off
xConfiguration Phonebook Server [1..5] ID:
<S: 0, 64>
Enter a name for the external phonebook. Addresses the specific phonebook.
Format: String with a maximum of 64 characters.
Example:
xConfiguration Phonebook Server 1 ID: “”
xConfiguration Phonebook Server [1..5] URL:
<S: 0, 255>
Enter the address (URL) to the external phonebook server. Addresses the specific phonebook server.
Format: String with a maximum of 255 characters.
Example:
xConfiguration Phonebook Server 1 URL: “http://tms.company.com/tms/
public/external/phonebook/phonebook.asmx”
The Phonebook settings
Contents
Introduction
Getting started
Interfaces
About the API
xConfiguration
xCommand
xStatus
Cameras
Appendices
Contact us
xConfiguration
