TANDBERG Codec 3000 MXP Reference Manual Download

Page: 97 / 242

TANDBERG 3000

MXP

6000

MXP

REFERENCE GUIDE FOR SYSTEM INTEGRATORS

Configuration-type Commands – xconfiguration / configuration.xml

D 13887.08
MAY 2008

Key

MicOff: <On/Off>

Enable or disable the given key (yellow Mic Off key) on the TANDBERG Remote Control, and using configuration instead of commands.

Example:

xconfiguration key micoff: on

Key

Presentation: <On/Off>

Enable or disable the given key (blue Presentation key) on the TANDBERG Remote Control, and using configuration instead of commands.

Example:

xconfiguration key presentation: on

Key

VolumeUp: <On/Off>

Enable or disable the given key () on the TANDBERG Remote Control, and using configuration instead of commands.

Example:

xconfiguration key volumeup: on

Key

VolumeDown: <On/Off>

Enable or disable the given key (Volume –) on the TANDBERG Remote Control, and using configuration instead of commands.

Example:

xconfiguration key volumedown: on

Key

Ok: <On/Off>

Enable or disable the given key (OK - Menu key) on the TANDBERG Remote Control, and using configuration instead of commands.

Example:

xconfiguration key ok: on

Key

ZoomIn: <On/Off>

Enable or disable the given key (Zoom +) on the TANDBERG Remote Control, and using configuration instead of commands.

Example:

xconfiguration key zoomin: on

Key

ZoomOut: <On/Off>

Enable or disable the given key (Zoom –) on the TANDBERG Remote Control, and using configuration instead of commands.

Example:

xconfiguration key zoomout: on

Key

Grab: <On/Off>

Enables/disables the signal which is sent to the codec when grabbing and touching the rubber lines on each side of the TANDBERG Remote Control.

Example:

xconfiguration key grab: on

Key

Cabinet: <On/Off>

Enables/disables the headset key in front of the cabinet. Applies to TANDBERG 1000 MXP only.

Example:

xconfiguration key cabinet: on

Key

Presets: <On/Off>

Enable or disable the given key on the TANDBERG Remote Control (TRC4), and using configuration instead of commands.

Example:

xconfiguration key presets: on

Key

cont...

Summary of Contents for Codec 3000 MXP



















































































































































































































































Search results

Summary of Contents for Codec 3000 MXP

Reviews:

Related manuals for Codec 3000 MXP

Brands by name

Popular brands

TANDBERG Codec 3000 MXP, Reference Manual

Search results

Summary of Contents for Codec 3000 MXP

Reviews:

Related manuals for Codec 3000 MXP

Brands by name

Popular brands