manualshive.com logo in svg

TANDBERG Codec 3000 MXP, Reference Manual

Share
Download
TANDBERG Codec 3000 MXP Reference Manual Download Page 158

158

TANDBERG 3000 

MXP 

&

 

6000 

MXP

 REFERENCE GUIDE FOR SYSTEM INTEGRATORS

Command Information

D 13887.08
MAY 2008

Required parameters are identified by an 

(r)

 appended to the parameter name. The 

(r)

 appears in this table for your information only and shall not be included when writing the commands – see the column

 Example

 for an illustration of this. Empty lines in the examples provided may have been removed to save space in the tables.

Command

Description

Parameters

Result parameters 

when OK

Result parameters 

when error

Example

KeyRelease

Command used to 
emulate release an 
already pressed key on 
the TANDBERG MXP 
remote control. The 
KeyRelease command 
should be preceded by 
a KeyDown command to 
emulate pressing the key.

Key

(r)

: <0/1/2/3/4/5/6/7/8/ 

9/*/#/Connect/Disconnect/
up/Down/Right/Left/Selfview/
Layout/Phonebook/Cancel/
MicOff/Presentation/Volumeup/
VolumeDown/OK/ZoomIn/
ZoomOut/Grab>

None

As above

xcommand keyrelease key: phonebook

*r Result (status=OK):

*r/end

OK

KeyPress

Command used to 
emulate pressing a 
key on the TANDBERG 
MXP remote control 
for a short while. This 
command needs no 
release command.

Key

(r)

: <0/1/2/3/4/5/6/7/8/ 

9/*/#/Connect/Disconnect/
up/Down/Right/Left/Selfview/
Layout/Phonebook/Cancel/
MicOff/Presentation/Volumeup/
VolumeDown/OK/ZoomIn/
ZoomOut/Grab>

None

As above

xcommand keypress key: phonebook

*r Result (status=OK):

*r/end

OK

KeyDisable

Command used to 
disable a key on the 
TANDBERG MXP remote 
control.

Key

(r)

: <0/1/2/3/4/5/6/7/8/ 

9/*/#/Connect/Disconnect/
up/Down/Right/Left/Selfview/
Layout/Phonebook/Cancel/
MicOff/Presentation/Volumeup/
VolumeDown/OK/ZoomIn/
ZoomOut/Grab>

None

As above

xcommand keydisable key: micoff

*r Result (status=OK):

*r/end

OK

KeyEnable

Command used to 
enable a key on the 
TANDBERG MXP remote 
control.

Key

(r)

: <0/1/2/3/4/5/6/7/8/ 

9/*/#/Connect/Disconnect/
up/Down/Right/Left/Selfview/
Layout/Phonebook/Cancel/
MicOff/Presentation/Volumeup/
VolumeDown/OK/ZoomIn/
ZoomOut/Grab>

None

As above

xcommand keyenable key: micoff

*r Result (status=OK):

*r/end

OK

KeyRelease — KeyEnable

Summary of Contents for Codec 3000 MXP



















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands