TANDBERG Codec 3000 MXP Reference Manual Download Page 68

Page: 68 / 242

TANDBERG 3000

MXP

6000

MXP

REFERENCE GUIDE FOR SYSTEM INTEGRATORS

Configuration-type Commands – xconfiguration / configuration.xml

D 13887.08
MAY 2008

Audio

Stereo: <On/Off>

Turns stereo I/O mode On or Off.

Example:

xconfiguration audio stereo: on

Stereo Settings

Output Response Codec 3000 MXP

Output Response Codec 6000 MXP

Out 1
mode

Stereo

I/O mode

Stereo

speakers

Audio Out 1

Audio Out 2

Audio Out 1

Audio Out 2

Audio
Out 3

Analogue

Off

Loudspeaker mono

VCR

Loudspeaker mono

Aux

VCR

Analogue

Off

Loudspeaker L

Loudspeaker R

Loudspeaker L

Loudspeaker R

VCR

Analogue

Off

Loudspeaker mono

VCR

Loudspeaker mono

VCR L

VCR R

Analogue

Loudspeaker L

Loudspeaker R

Loudspeaker L

Loudspeaker R

VCR

SPDIF

Off

Loudspeaker mono

VCR

Loudspeaker mono

Aux

VCR

SPDIF

Off

Loudspeaker L & R

VCR

Loudspeaker L & R

Aux

VCR

SPDIF

Off

Loudspeaker mono

VCR

Loudspeaker mono

VCR L

VCR R

SPDIF

Loudspeaker L & R

VCR

Loudspeaker L & R

VCR L

VCR R

Out 1 mode is controlled through the

xconfiguration audio outputs line type

command (overleaf)

Audio

StereoSpeakers: <On/Off>

Turns stereo speakers On or Off.

Example:

xconfiguration audio stereospeakers: on

Audio

VCRDucking: <On/Off>

If VCR Ducking is set to

, the VCR audio level will be attenuated if someone talks into the microphone or at the far end.

Example:

xconfiguration audio vcrducking: on

Audio

KeyTones: <On/Off>

If set to

there will be a sound indicator when pressing keys on the remote control.

Example:

xconfiguration audio keytones: on

Audio

Inputs

Microphone [1..x]

6000 MXP: x=3
3000 MXP: x=2

Level: <1..16>

Defines the input levels for the different microphones.

Example:

xconfiguration audio inputs microphone 2 level: 10

By default, all inputs are
enabled. Just plug in an audio
source and it is active. Audio
inputs that are

will auto-

matically be mixed. Unconnected
inputs will automatically be
muted. Select

Off

to prevent

audio/noise from connected but
unused inputs.

The microphone inputs are
intended for electret type micro-
phones. The microphone inputs
are balanced with 24 V phantom
power.

Audio

Inputs

Microphone [1..x]

6000 MXP: x=3
3000 MXP: x=2

Mode: <On/Off>

Turns On or Off the different microphone inputs.

Example:

xconfiguration audio inputs microphone 2 mode: off

Turns microphone 2 off.

Audio

Inputs

Microphone [1..x]

6000 MXP: x=3
3000 MXP: x=2

Mode: <Line>

NOTE!

Applies to 6000 MXP only! Here the Microphone 3 Mode can be set to Line. It then

becomes a balanced line level input. The gain will be reduced accordingly.

Example:

xconfiguration audio inputs microphone 3 mode: line

Sets microphone input 3 on a 6000 MXP to a balanced line level input.

Audio

Inputs

Line [1..x]

6000 MXP: x=3
3000 MXP: x=2

Level: <1..16>

Defines the input levels for the different line inputs.

Example:

xconfiguration audio inputs line 2 level: 10

Audio

cont...

Summary of Contents for Codec 3000 MXP



















































































































































































































































Search results

Summary of Contents for Codec 3000 MXP

Reviews:

Brands by name

Popular brands

TANDBERG Codec 3000 MXP, Reference Manual

Search results

Summary of Contents for Codec 3000 MXP

Reviews:

Brands by name

Popular brands