manualshive.com logo in svg

TANDBERG Codec 3000 MXP, Reference Manual

Share
Download
TANDBERG Codec 3000 MXP Reference Manual Download Page 89

89

TANDBERG 3000 

MXP 

&

 

6000 

MXP

 REFERENCE GUIDE FOR SYSTEM INTEGRATORS

Configuration-type Commands – xconfiguration / configuration.xml

D 13887.08
MAY 2008

IMUX

Custom

BW1920R

Suffix: <S: 0, 12>
Defines the suffix to be used with the RS366 Custom IMUX at this restricted bandwidth.

Example:

 xconfiguration imux custom bw1920r suffix: xxx

Integrator

AMXBeacon

Mode: <On/Off>

If set to 

On

, the system will start transmitting beacon messages to support AMX’s Dynamic Device Discovery Protocol (DDDP). The beacon string is trans-

mitted as a UDP packet to 239.255.250.250 on port 9131 at random intervals between 30 and 60 secs. The transmission of the Beacon message is by 
default set to 

Off

.

Example:

 xconfiguration integrator amxbeacon mode: off

Integrator

Telepresence

Mode: <Off/Point2Point/MultiPoint/Briefer>

Only in use with TANDBERG Experia.

Example:

 xconfiguration integrator telepresence mode: off

IP

Assignment: <DHCP/Static>

Defines whether to use DHCP or Static IP assignment. NOTE! This configuration only applies to IPv4.

Example:

 xconfiguration ip assignment: dhcp

IP

Address: <IPAddr>

Defines the IPv4 address to use. Only applicable if Static IP assignment is being used.

Example:

 xconfiguration ip address: 

IP

SubnetMask: <IPAddr>

Defines the subnet mask. Only applicable if Static IP assignment is being used.

Example:

 xconfiguration ip subnetmask: 

IP

V6

Address: <IPv6Addr: 0, 43>

Allows static configuration of IP v6 Address.

Example:

 xConfiguration ip v6 address:

IP

Gateway: <IPAddr>

Defines the gateway address. Only applicable if Static IP assignment is being used.

Example:

 xconfiguration ip gateway: 

IP

DNS

Server [1..5]

Address: <IPv4v6Addr: 0, 43>

Defines the network addresses for DNS servers. Up to 5 addresses may be specified. If the network addresses are unknown, 

please contact your administrator or Internet Service Provider.

Example:

 xconfiguration ip dns server: 

IP

DNS

Domain

Name: <S: 0, 64>

DNS Domain Name is the default domain name suffix which is added to unqualified names.

Example:

 DNS Domain Name is “

example.com

”, and the name to lookup is “

videosystem

” will result in a “

videosystem.

example.com

” DNS lookup. 

IMUX 

cont...

 — IP

Summary of Contents for Codec 3000 MXP



















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands