TANDBERG Codec 3000 MXP Reference Manual Download | Manualshive

Page: 111 / 242

background image

111

TANDBERG 3000

MXP

&

6000

MXP

REFERENCE GUIDE FOR SYSTEM INTEGRATORS

Configuration-type Commands – xconfiguration / configuration.xml

D 13887.08
MAY 2008

SerialPort [1]

Direct

Buffer: <0..16384>

NOTE!

Port 1 Only

Specifies the size of the buffer used in direct mode. Try setting this value higher if you need a continuous stream of data on the receiving end. Higher

values introduces more delay.

Example:

xconfiguration serialport 1 direct buffer: 5120

SerialPort [1..2]

BaudRate: <1200/2400/4800/9600/19200/38400/57600/115200>

Specify the baud rate on a serial port.

Example:

xconfiguration serialport 1 baudrate: 9600

SerialPort [1..2]

Parity: <None/Odd/Even>

Specify the Parity on a Serial Port

Example:

xconfiguration serialport 1 parity: odd

SerialPort [1..2]

DataBits: <7/8>

Specify the number of databits on a Serial Port

Example:

txconfiguration serialport 1 databits: 7

SerialPort [1..2]

StopBits: <1/2>

Specify the number of stopbits on a Serial Port

Example:

xconfiguration serialport 1 stopbits: 2

SIP

Mode: <On/Off>

On:

Setting the SIP mode to on will enable the system for incoming and outgoing SIP calls.

Off:

Setting the SIP mode to off will disable incoming and outgoing SIP calls from the system.

Example:

xconfiguration sip mode: on

SIP

ReplyTo

URI: <S: 0, 60>

If configured it is this URI that will be displayed in the call lists.

Example:

xconfiguration sip replyto uri:

SIP

Server

Discovery: <Manual/Auto>

Manual:

When Manual is selected, the manually configured SIP Server address will be used

Auto:

When Auto is selected, the SIP Server address is obtained using Dynamic Host Configuration Protocol (DHCP).

Example:

xconfiguration sip server discovery: manual

SIP

Server

Address: <S: 0, 255>

The Server Address is the manually configured address for the outbound proxy and registrar. It is possible to use a fully qualified domain name, or an IP

address. The default port is 5060 for TCP and UDP, but another one can be provided

Example:

xconfiguration sip server address:

SerialPort

cont...

— SIP

«
...
109
110
111
112
113
...
»

Summary of Contents for Codec 3000 MXP



















































































































































































































































Reviews:

No comments

Related manuals for Codec 3000 MXP

Spacemaker 7-5400

Brand: GE Pages: 12

CQDF783U - AUTO RADIO/CD DECK

Brand: Panasonic Pages: 5

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 145

Brand: Panasonic Pages: 66

Brand: E-Mu Pages: 72

Brand: E-Mu Pages: 44

MaestroKitchen 100

Brand: Harman Kardon Pages: 36

Triton Barrier TL-2

Brand: VALTIR Pages: 28

VC210 Teams Edition

Brand: Yealink Pages: 32

Brand: Belson Pages: 34

Brand: Audio System Pages: 2

InfoView IV 2000

Brand: InnoMedia Pages: 50

Brand: Mircom Pages: 149

Brand: Matrix Telecom Pages: 98

Brand: Panasonic Pages: 100

Brand: Raven Pages: 47

L-force PROFINET E94AYCER

Brand: Lenze Pages: 114

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands