manualshive.com logo in svg

TANDBERG Codec 3000 MXP, Reference Manual

Share
Download
TANDBERG Codec 3000 MXP Reference Manual Download Page 170

170

TANDBERG 3000 

MXP 

&

 

6000 

MXP

 REFERENCE GUIDE FOR SYSTEM INTEGRATORS

Status Information – xstatus /xstatus.xml

D 13887.08
MAY 2008

Status information followed by a

 

*

 

will not be shown unless Detailed Level has been set to 2

 

–

 

see 

XACLI – Special commands – xpreferences

Call [1..10]

(status=

Disconnected / CallIDLE / Dialing / Alerting / Proceeding / EstablOut / EstablIn / AwaitInCnf / Connected / Disconnecting / Await2ndnr / ClearOut / ClearIn / Syncing / Capex / Synced / Unframed

,

type = 

NA / Tlph / Vtlph

,

protocol = 

NA / ISDN / H320 / H323 / SIP,

direction = 

NA / Incoming / Outgoing

,

logTag = 

1..x

 )

If status = 

Disconnected

 

and type = 

NA

 

and protocol = 

NA

 

and direction = 

NA

 

and logtag = 

x

  

the following will be included:

  Cause:

If status = 

Dialing / Alerting / Proceeding / EstablOut / EstablIn / AwaitInCnf / Connected / Disconnecting / Await2ndnr / ClearOut / ClearIn / Syncing / Capex / Synced / Unframed

 

and type = 

Tlph

 

and protocol = 

ISDN

 

and direction = 

Incoming / Outgoing

 

and logTag = 

x

the following will be included:

CallRate:

 64

RemoteNumber [1..2]:

RemoteSubAddress:

IncomingNumber:

 

Appears for incoming calls only

IncomingSubAddress:

Mute:

 On/Off

Microphone:

 On/Off

Duration:

 0...

MuteOutgoing:

 On/Off

Channels [1..2] 

(type = 

Incoming / Outgoing

)

:

If type = 

incoming

 

/

 

outgoing

 the following will be included:

Rate:

 64

Restrict:

 On/Off

Audio

 (status =

 

Active / Inactive

)

:

Call

Summary of Contents for Codec 3000 MXP



















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands