manualshive.com logo in svg

TANDBERG Codec 3000 MXP, Reference Manual

Share
Download
TANDBERG Codec 3000 MXP Reference Manual Download Page 71

71

TANDBERG 3000 

MXP 

&

 

6000 

MXP

 REFERENCE GUIDE FOR SYSTEM INTEGRATORS

Configuration-type Commands – xconfiguration / configuration.xml

D 13887.08
MAY 2008

CallVideoSource: <0/1/5/6>

The Call Video Source is the default call video source you would prefer to use in a call..

Example:

 xconfiguration callvideosource: 0

Camera [1..13]

Brightness

Mode: <Manual/Auto>

Sets whether to control camera brightness of the different cameras manually or to have it automatically set by the 
system.

Example:

 xconfiguration camera 1 brightness mode: manual

If a TANDBERG Video Switch is 
connected, the camera ranges 
will behave as follows:

Camera 1 will be the video 

• 

switch. 
Camera range 2..7 will 

• 

be cameras connected to 
secondary chain (the chain 
originating from Data port 2 
of the switch). 
Camera range 8..13 will be 

• 

cameras connected to the 
primary chain (the chain 
originating from Data port 1 
of the switch).

Go to the 

TANDBERG Video 

Switch

 section to read more.

Camera [1..13]

Brightness

Level: <0..16>

Defines the brightness level to use if Brightness Mode is set to 

Manual

.

Example:

 xconfiguration camera 1 brightness level: 10

Camera [1..13]

Whitebalance

Mode: <Manual/Auto>

If set to 

Auto

 the camera will continuously adjust the whitebalance depending on the camera view.

When set to 

Manual

 the whitebalance can be calibrated manually by the command 

CameraWhiteBalance

. The white-

balance of the camera will then remain constant until a new calibration is performed.  

Example:

 xconfiguration camera 1 whitebalance mode: auto

Camera [1..13]

Whitebalance

Level: <0..16>

Specifies the camera whitebalance level. Applies to TANDBERG Precision HD cameras only.

Example:

 xconfiguration camera 1 whitebalance level: 10

Camera [1..13]

Focus

Mode: <Manual/Auto>

If set to 

Manual

 autofocus will never be turned on automatically.

Example:

 xconfiguration camera 1 focus mode: manual

Camera [1..13]

Backlight: <On/Off>

Turns backlight compensation of camera On/Off. Not applicable to TANDBERG WAVE I cameras.

Example:

 xconfiguration camera 1 backlight: on

Camera [1..13]

DualVisca: <Off/On> 

Enables or disables dual visca mode. If enabled, visca control will be available on the RJ11 connector on the camera. If disabled, the RJ11 
connector will work as a normal daisy chain port. Applies to TANDBERG Precision HD cameras only.  

Example:

 xconfiguration camera 1 dualvisca: on

Camera [1..13]

Mirror: <Off/On>

Turns mirror mode on/off. Not applicable to TANDBERG WAVE I cameras.

Example:

 xConfiguration camera 1 mirror: on

CallVideoSource — Camera [1..13]

Summary of Contents for Codec 3000 MXP



















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands