0-6
Operation .........................................3-1
Before starting operation ......................... 3-2
Getting on or off the machine ............... 3-2
Walk-around inspection ....................... 3-2
Daily inspection .................................... 3-2
Starting and stopping the engine ............. 3-3
Before starting the engine .................... 3-3
Starting the Engine .............................. 3-4
Warming up the engine ........................ 3-5
Stopping the engine ............................ 3-5
Operating the machine ............................ 3-6
Lever pattern (ISO pattern) ................... 3-6
Lever pattern (G pattern) (If equipped) .. 3-7
Warming up the machine (hydraulic oil) 3-8
Inspection after warm-up ................... 3-10
Traveling the machine ........................ 3-10
Stopping travel .................................. 3-15
Operating the working equipment ...... 3-15
Operating procedures ............................ 3-18
Prohibited operations ......................... 3-18
Precautions for operation ................... 3-21
Precautions when traveling on slopes 3-22
Getting out of mud ............................ 3-24
Operations possible with this
machine............................................. 3-25
Parking the machine .............................. 3-26
Parking .............................................. 3-26
Inspection and checks after stopping
the engine.......................................... 3-27
Handling in cold climates ....................... 3-28
Preparing for cold climates ................ 3-28
Cautions after operations ................... 3-28
After the cold climate ......................... 3-28
Handling tires ........................................ 3-30
Prohibitions ........................................ 3-30
Precautions ....................................... 3-31
Transport .........................................4-1
Loading and unloading ............................ 4-2
Hoisting the machine ............................... 4-4
Securing the machine .............................. 4-6
Transporting posture ............................ 4-6
Precautions to be taken during
transportation .......................................... 4-7
Maintenance ....................................5-1
General .................................................... 5-2
Maintenance overview ......................... 5-2
Cautions on maintenance .................... 5-2
Service data ............................................ 5-4
Fuel and lubricant table ........................ 5-4
Regularly replace the hydraulic oil ........ 5-8
List of consumables ............................. 5-9
List of tools (If equipped) .................... 5-10
List of tightening torques ................... 5-11
Safety-critical parts ................................ 5-12
Maintenance list ..................................... 5-14
Walk-around inspection ......................... 5-16
Inspecting by opening the engine hood
and covers......................................... 5-16
Inspecting by walking around the
machine............................................. 5-17
Inspecting while sitting in the operator’s
seat ................................................... 5-17
Daily inspection (every 10 hours) ............ 5-18
Inspecting and replenishing the
coolant .............................................. 5-18
Inspecting and replenishing the
engine oil ........................................... 5-19
Inspecting the water separator and
the fuel filters ..................................... 5-20
Inspecting the fuel level ...................... 5-21
Inspecting the hydraulic oil tank level
and replenishing ................................ 5-22
Lubricating the working equipment .... 5-23
Inspecting and inflating the tires ......... 5-24
Checking the wheel nut torques ......... 5-25
After the initial 50 hours
(only for new machines) ......................... 5-26
Replacing the engine oil and the oil
filter ................................................... 5-26
Inspecting and adjusting the V-belt .... 5-28
Inspecting and adjusting the
compressor belt (AC) ......................... 5-29
Replacing the hydraulic oil return filter 5-30
Replacing the pilot line filter ................ 5-31
Replacing the travel line filter .............. 5-32
Every 50 hours ...................................... 5-34
Lubricating the slew bearing .............. 5-34
Draining the water from the fuel tank .. 5-35
Inspecting the battery fluid level and
replenishing ....................................... 5-36
After the initial 100 hours
(only for new machines) ......................... 5-38
Replacing the transmission gear oil .... 5-38
Replacing the differential gear oil ....... 5-38
Replacing the hub gear oil ................. 5-39
Every 250 hours .................................... 5-40
Summary of Contents for TB295W
