Symmetricom ATS-6511A Page 73 User Manual Download | Manualshive

Page: 73 / 115

background image

DOC 6511_Release K

ATS-6511A/B/C Users Guide

67

                     [status] good
               [power] enabled
               [type] 4394A
            [2-4]

Same as slot 1 for the card installed

[5]
[type] empty

Indicates a card is not installed.

            [6]
               [type] empty
         [warmstartable] true

Unit has enough data to warmstart

[power]

Power Supply Information

[numsupplies] 2

# of Supplies Operating

[supplies]
[1]

Left Power Supply

[status] good

Current Status

[type] 4385A

Model #

[2]

Right Power Supply

[status] good

Same as Supply #1

[type] 4385A
[temperature] 30

Internal Temperature ºC

[health]

Operating Status Information

[clock_wander]

Clock Issues.

[active] false

Active = True for current alarm

[cleared]

When the alarm condition cleared

[what] Clock wander is less than 100.000000ns

What cleared

[when] 1998-01-01-00:06:49.651

When it cleared

[occurrences] 1

# of times the alarm has occurred

[set]

When the alarm happened

[what] Clock wander exceeded 100.000000ns

What happened

[when] 1998-01-01-00:06:47.534

When it occurred

[fan]

Fan Issues

         [1]
            [active] false
            [occurrences] 0
         [2]
            [active] false
            [occurrences] 0
      [fiber_signal_present]

Fiber Issues

         [active] false
         [cleared]
            [what] Fiber signal is present
            [when] 2011-06-09-21:26:38.331
         [occurrences] 1
         [set]
            [what] Fiber signal is missing

Note: This is the date when the unit is first

[when] 1998-01-01-00:02:31.457

powered up - the date/time has not been set.

      [firmware_version_mismatch]
         [active] false
         [occurrences] 0

[hardware_internal]

Internal Clock Issues

         [active] false
         [occurrences] 0
      [holdover_ref_comm_error]
         [active] false
         [occurrences] 0
      [holdover_ref_missing]
         [active] false
         [occurrences] 0
      [holdover_ref_unlocked]
         [active] false

«
...
71
72
73
74
75
...
»

Summary of Contents for ATS-6511A




















































































































Reviews:

No comments

Related manuals for ATS-6511A

Brand: EBS Pages: 4

Brand: EAW Pages: 16

Brand: Pass Pages: 6

Rampage AXTM-600

Brand: Audiovox Pages: 12

Brand: Channel D Pages: 8

Brand: Crest Audio Pages: 18

Tube Location GA-9

Brand: Gibson Pages: 1

Brand: AKG Pages: 16

Brand: Crest Audio Pages: 2

Brand: Tapco Pages: 34

Brand: Atoll Electronique Pages: 3

Brand: Forney Pages: 53

Pro-Ject Head Box S

Brand: Pro-Ject Audio Systems Pages: 3

Brand: Majorcom: Pages: 7

Brand: Parasound Pages: 7

Brand: Russound Pages: 51

Multichannel Power Amplifier G55

Brand: Meridian Pages: 2

q1000 Power Amp

Brand: DV Mark Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands